Dreame U10 Manual De Usuario página 8

Only use accessories and replacement parts recommended by the manufacturer.
•
EN Please be extra careful when using the vacuum to clean stairs.
•
Make sure the vacuum is unplugged when not used for extended periods as well as
•
prior to performing any maintenance or repairs.
Do not install, charge, or use this product outdoors, in bathrooms, or around a pool.
•
Fire Hazard Warning: Do not apply any type of fragrance to the vacuum's filter. These
•
types of products are known to contain flammable chemicals which may cause the
vacuum to catch fire.
Only use the original charger (Model ZD012M300065EU). Failing to do so may cause
•
the lithium-ion battery to catch fire.
Only use the approved battery type (Model V2315-7S1P-SCA). Failing to do so may
•
cause the lithium-ion battery to catch fire.
• If the battery material is released, remove personnel from area until the batteries
cool down and fumes dissipate.
• Provide maximum ventilation to clear out hazardous gases and avoid skin and eye
contact or inhalation of vapors.
Remove spilled liquid with absorbent and incinerate waste.
•
Do not use and store in extremely hot or cold environments (below 0℃ /32℉or above
•
40℃ /104℉). Please charge the cordless vacuum in temperature above 0℃ /32℉and
below 40℃ /104℉.
This product is designed for home use only.
•
The supply terminals are not to be short-circuited.
•
Symbols
read operator's manual
detachable supply unit
We, Dreame Trading (Tianjin) Co., Ltd., hereby, declares that this equipment is in
compliance with the applicable Directives and European Norms, and amendments.
The full text of the EU declaration of conformity is available at the following internet
address: https://global.dreametech.com
For detailed e-manual, please go to https://global.dreametech.com/pages/user-
manuals-and-faqs
10
Accessories
Note: The illustrations in this manual are
indicative only. The actual product may
differ.
1. Extension Rod
2. Combination Tool
3. Charger
4. Multi-Surface Brush
5. Wall Mount (Including screw × 2, wall
plug × 2)
Fig. A
Components
1. Power Button (Press to turn on/Release
to turn off)
2. Suction Level Status Indicator
Turbo Med Eco
3. Suction Level Switch
4. Dust Cup
5. Dust Cup Release Button
6. Multi-Surface Brush
7. Antistatic Contact
8. Battery Status Indicator
9. Battery Pack Release Button
10. Charging Port
11. Extension Rod Release Button
12. Extension Rod
13. Brush Release Button
Fig. B
Installation
• Vacuum and Accessories Installation
Fig. C-1
• Wall Mount Installation
The mount should be installed in a cool,
dry place near a power outlet. Make sure
the installation area is clear of any pipes
such as gas or water lines, and air ducts,
electric wires and cables, or drainage
lines.
1. Before installation, measure the wall
in the height of 102 cm (40.2 inches)
above the ground.
2. Mark and drill two 8 mm (0.315 inch)
diameter holes into the wall with an
electric drill.Insert the wall plugs into
the holes.
3. Align the position holes on the mount
with the holes on the wall. Fasten it to
the wall with the included screws.
Fig. C-2
Operation
Charging
• Connecting the charger to the wall
mount
1. Rotate the clip in the bottom of wall
mount 90 degrees counterclockwise to
remove it from the mount.
2. Insert the power cord into the notch on
the clip.
3. Rotate the clip 90 degrees clockwise
until it clicks into place.
Fig. D-1
• Put the vacuum cleaner on the wall
mount and plug the charger into the
charging port.
Fig. D-2
• Battery Status Indicator
Fig. D-3
Charging
Fully charged
Charging
Discharging
Battery Level ≥ 10%
Battery Level < 10%
Solid white Blinking white off
Note:
1. The vacuum cannot be used while
charging.
2. Fully charge the vacuum before using
it for the first time. This will take about
3 hours.
3. Vacuuming at Turbo mode for a
prolonged period will cause the battery
EN
11