Publicidad
Idiomas disponibles
Idiomas disponibles
20.
Pay attention to the dimension of the blades. The
centre hole in the blade must fit on the arbor with
no free play. If not, a reducer washer (provided with
the blade) will be needed to ensure proper fit.
2.4 Work area
Work position
A. POSITION OF TILE SAW
1.
To avoid the possibility of the appliance plug or
receptacle getting wet, position tile saw to one
side of a wall mounted receptacle to prevent water
from dripping onto the receptacle or plug. The user
should arrange a "drip loop" in the cord connecting
the saw to a receptacle.
The "drip loop" is that part of the cord below the
level of the receptacle, or the connector if an
extension cord is used, to prevent water traveling
along the cord and coming in contact with the
receptacle.
2.
If the plug or receptacle does get wet, DON'T unplug
the cord. Disconnect the fuse or circuit breaker
that supplies power to the tool. Then unplug and
examine for presence of water in the receptacle.
B. EXTENSION CORDS
1.
Use only extension cords that are intended for
outdoor use. These extension cords are identified
by a marking "Acceptable for use with outdoor
appliances; store indoors while not in use." Use
only extension cords having an electrical rating
not less than the rating of the product. Do not use
damaged extension cords. Examine extension cord
before using and replace if damaged. Do not abuse
extension cords and do not yank on any cord to
disconnect. Keep cord away from heat and sharp
edges. Always disconnect the extension cord from
the receptacle before disconnecting the product
from the extension cord.
2.
WARNING – To reduce the risk of electrocution,
keep all connections dry and off the ground. Do not
touch plug with wet hands.
3.
Ground Fault Circuit Interrupter (GFCI) protection
should be provided on the circuit(s) or outlet (s) to
be used for the tile saw. Receptacles are available
having built-in GFCI protection and may be used for
this measure of safety.
3.- GROUND CONNECTION INSTRUCTIONS
All tools must be connected to ground: (Figure 1)
In case of malfunction or fault, the ground connection
provides a path of least resistance for the electrical
current in order to reduce the risk of electric shock. This
tool is equipped with an electrical cable for connecting
the equipment to ground and an grounded plug. The plug
must be plugged into a corresponding power outlet that is
· TRANSLATION OF THE ORIGINAL · ENGLISH
English
English
correctly installed and connected to ground in accordance
with all the local codes and ordinances.
Do not modify the plug provided. If it does not fit the
power outlet, get a qualified electrician to install a suitable
power outlet.
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. The
conductor with insulation having an outer surface that is
green with or without yellow stripes is the equipment-
grounding conductor. If repair or replacement of the
electric cord or plug is necessary, do not connect the
equipment-grounding conductor to a live terminal.
Check with a qualified electrician or service personnel
if you do not fully understand the ground connection
instructions, or if you have any doubts whether the tool is
correctly connected to ground.
Immediately repair or replace a damaged or worn cable.
This saw is designed for use in a 120 V nominal circuit and
has an grounded plug. Only connect the saw to a power
outlet that has the same configuration as the plug. Do not
use an adapter with this product.
4.- MACHINE/COMPONENT
CHARACTERISTICS
4.1 Technical specifications
Blade diameter
Arbor diameter
Cutting capacity (tile size)
Diagonal cutting capacity (tile size)
Maximum cutting height
Voltage
Speed
4.2 Machine components
The safe use of this product requires knowledge of the tool
and of this operator's manual. Before using this product,
familiarise yourself with all its characteristics, components
and safety rules.
•
7 INCH DIAMOND BLADE included with the machine.
WARNING do not use blades with a classification
lower than the speed of this tool. Ignoring this
warning could result in personal injury.
•
HANDLES located on the left and right sides for lifting
and transporting.
•
ANGLE GUIDE for diagonal cuts.
•
TILTING TABLE for miter cuts of 22.5° and 45°.
•
REAR TABLE EXTENSION to support large tiles of up to
24in length when making longitudinal cuts.
•
MOTOR with sufficient power to carry out difficult
cutting work.
EN
7 in.
5/8 in.
20 in.
13 in.
1-1/4 in
120 V / 60 Hz,
6.5 A
3450 r/min.
(RPM)
- 5 -
Publicidad
