Publicidad
Idiomas disponibles
Idiomas disponibles
ENglish
WARNING: Always wear proper personal hearing
protection that conforms to ANSI S12.6 (S3.19) during
use. Under some conditions and duration of use, noise from
this product may contribute to hearing loss.
CAUTION: When not in use, place tool on its side
on a stable surface where it will not cause a tripping
or falling hazard. Some tools with large battery packs will
stand upright on the battery pack but may be easily knocked over.
• Air vents often cover moving parts and should be
avoided. Loose clothes, jewelry or long hair can be caught in
moving parts.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ......................... volts
Hz ....................... hertz
min ..................... minutes
or DC ...... direct current
...................... Class I Construction
(grounded)
.../min .............. per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
A ......................... amperes
W ........................ watts
or AC ........... alternating current
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
n o ....................... no load speed
n ......................... rated speed
...................... earthing terminal
..................... safety alert symbol
..................... visible radiation
..................... wear respiratory
protection
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/installing
attachments or accessories. An accidental start‑up can
cause injury.
Attaching Hook and Loop Sanding Discs (Fig. B)
Your sander is designed to use 5" (127 mm) sanding discs
with the 8 hole dust extraction pattern. Sanding discs attach
with hook and loop.
1. To attach the sanding disc
sanding pad
3
ensuring the holes in the disc align with the
holes in the pad and press the disc firmly in place.
6
..................... wear eye
protection
..................... wear hearing
protection
..................... read all
documentation
-1
../min or ..min
. Revolutions or
Reciprocations per
minute
2
.................. two phase
alternating current
2N
............... two phase
alternating current
with neutral
3
.................. three phase
alternating current
3N
............... three phase
alternating current
with neutral
..................
rated current of the
x
appropriate fuse-
link in amperes
............ time-log miniature
A
fuse-link where X
is the symbol for
the time/current
characteristic, as
given in
IEC 60127-3
IPXX .................... IP symbol
9
, carefully center it over the
2. The hook and loop fastening system sanding disc can
be easily removed by simply pulling it off. It can be reused
as desired.
Dust Collection (Fig. C, D)
WARNING: Collected sanding dust from sanding
surface coatings (polyurethane, linseed oil, etc.) can
self‑ignite in sander dust bag or elsewhere and cause
fire. To reduce risk, empty bag frequently and strictly follow
sander manual and coating manufacturer's instructions.
• The dust bag
should be emptied after every 10 minutes
5
of sanding.
• To attach the dust bag to the sander, line up the grooves
on the side dust bag collar
on the dust port
4
.
• Slide the dust bag
onto the dust port and turn the dust
5
bag clockwise to lock it in place.
• To remove, turn the dust bag
slide off the dust bag.
• To empty the dust bag, remove it from the dust port and
dump the sanding debris into an appropriate trash receptacle.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/installing
attachments or accessories. An accidental start‑up can
cause injury.
Installing and Removing the Battery Pack (Fig. E)
NOTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
battery pack with the rails inside the tool's handle and slide
it into the handle until the battery pack is firmly seated in
the tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button
and firmly pull the battery pack out of the tool
7
handle. Insert it into the charger.
Proper Hand Position (Fig. F)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the main
handle
as shown in Figure F.
1
On/Off Switch (Fig. A)
• To switch the tool on, depress the on/off switch
"I" position.
• To switch the tool off, depress the on/off switch
"O" position.
Sander Operation
WARNING: Let the tool work at its own pace. Do
not overload.
Grasp the sander and turn it ON. Move it in long, sweeping
strokes along the surface, letting it do the work. Pushing
down on the tool while sanding actually slows the removal
rate and produces an inferior quality finish.
Check your work often. This sander is capable of removing
material rapidly.
with the dust bag locks
11
counterclockwise and
5
6
into the tool handle, align the
2
2
10
12
at the
at the
Publicidad
