Publicidad
Idiomas disponibles
Idiomas disponibles
2. Pull the lock lever
10
cutter housing
11
.
3. Slide the cutter
12
out of the housing.
To Install
1. Slide the new cutter into the housing, ensuring the cutter
fits properly in the housing
2. Push the house together and close the lock lever until it
clicks securely into place (as shown in Fig. H).
nOTE: The gear teeth should be meshed and the door
should not be forced close. If heavy resistance is experienced,
please check for proper alignment and retry.
OPERATION
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Introduction
The DWACPRIR Impact Connect Copper Tubing Cutter uses
a compatible impact driver to rotate copper cutters around
pipe. Copper Cutters can be driven by the attachment or
used manually.
•
Forward setting: Squeezing the trigger with the impact
driver set to forward (clockwise) rotates the copper
cutters clockwise.
WARNING: CRUSH HAZARD: Keep fingers away from
cutting area. Failer to do so can cause injury.
WARNING: Proper material preparation and installation is
the responsibility of the installing contractor.
WARNING: Do not cut short pieces of material that
requires hands to be within 6" from the blade. Blade
is sharp.
CAUTION: Do not cut off pieces of tubing less than ½"
long. Small pieces can be pulled into moving carriage
and damage tool.
Proper Hand Position (Fig. I)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the main handle
of the impact driver.
Cutting Copper Tubing (Fig. J)
This tool can cut 1/2", 3/4", and 1" copper tubing with the
approved accessories.
1. Mark the cutting point on the tubing.
2. Secure tubing to prevent it from moving while cutting.
3. Insert the tubing into the cutter
blade
13
and cutter wheels
4. Align the blade with mark.
5. Set the impact driver to forward (clockwise).
6. Depress the trigger of the impact driver.
7. After the tubing is fully cut, release the trigger .
away from the tool to loosen the
12
between the cutter
14
.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Your D
WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product, use
e
of such accessories with this product could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Recommended accessories for use with your product are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact D
(1‑800‑433‑9258) or visit our website: www.dewalt.com
Repairs
The cutter, charger, and batteries are not serviceable.
There are no serviceable parts inside the cutter, charger, or
battery pack.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement, when applicable) should
be performed by a D
D
WALT authorized service center. Always use identical
e
replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• COnFiRMATiOn OF OWnERshiP: In case of an
insurance loss, such as fire, flood or theft, your registration
of ownership will serve as your proof of purchase.
• FOR YOUR sAFETY: Registering your product will allow
us to contact you in the unlikely event a safety notification
is required under the Federal Consumer Safety Act.
• Register online at www.dewalt.com.
English
WALT recommended
e
WALT call 1‑800‑4‑D
WALT
e
e
WALT factory service center or a
e
7
Publicidad
