Miniland digital camera 3.5' easy Manual Del Usuario página 12

ENGLISH
on, you can see the images and listen to the sounds
captured in your baby's room via the monitor.
5.2.2. SETTING THE CAMERA ANGLE
The camera on the 3.5" baby monitor can be angled
manually. To do this, turn the camera to the left or to
the right, and / or move the lens up or down until you
get the position you want. The camera has 355º vision,
but it does not rotate on its own axis, so do not force it.
When you turn the camera sideways and it reaches its
limit at around 180º, do not try to make it turn further.
The camera has a 53º vertical angle of view, so do not
force it when it reaches its limit.
Note: For a clearer view, clean the camera lens with
a slightly damp cloth.
5.2.3. INFRARED NIGHT VISION (AUTOMATIC)
The infrared night vision function allows the camera to
pick up images in dark or low light conditions. In this
mode, only black and white images will be displayed
on the monitor and only objects located less than 2
meters away can be seen.
The camera automatically changes to infrared mode
when there is insufficient light for normal vision.
When the camera is in this mode, the night vision icon
(D) will be displayed on screen.
Note: The light sensor (II) is located at the top of
the camera. Take care not to cover the sensor with
any object to prevent the camera from entering night
mode when there is light in the room.
5.2.4. ADD CAMERA AND PAIRING
The device is designed to allow different areas to be
observed with up to two cameras. To pair the camera
follow the steps described below:
1. Press the menu button (5) to display the menu and
show the highlighted camera icon.
2. Press the down (8) navigation button until the add
/ remove icon is displayed and press the OK / zoom
button (10) to go into the sub-menu.
3. Press the up (6) or down (8) navigation button to
select the camera you want to add.
4. Press the OK / zoom button (10) to search for a
camera unit.
5. Press the pairing button on the camera (X) for
5 seconds.
6. Once paired the image of the camera will show
immediately on the monitor unit screen.
For various reasons you may lose the connection
between the monitor and a camera which is already
connected. Should this be the case, repeat the process
explained above to connect the camera with the
monitor again.
Note 1: Before starting the pairing procedure, make
sure the camera and the monitor are close to one
another and that the camera is correctly plugged
in and is switched on.
Note 2: Each camera can be linked just with one
monitor at a time.
Nota 3: If the monitor and the camera, for some
reason, have left the factory without being paired,
you will have to do it manually adding the camera
to channel 2. You won't be able to pair the camera
again with channel 1 until you have paired it in
another channel and remove the channel 1 camera.
5.2.5. DELETE CAMERA
To delete one of the cameras connected, follow the
next steps:
1. Press the menu button (5) to display the menu and
show the highlighted camera icon.
2. Press the up (6) or down (8) navigation button
until the add / remove icon is displayed and then press
the OK / zoom button (10) to go into the sub-menu.
3. Press the up (6) or down (8) navigation button to
select the camera you want to remove and then press
the OK / zoom button (10) again.
Note: A channel needs to be deleted before pairing
to a new camera unit.
5.2.6. CHOOSING THE CAMERA
The device is designed to allow different areas to be
monitored with up to two cameras.
To select the camera you want to view, follow the steps
described below:
1. Press the menu button (5) to display the menu and
show the highlighted camera icon.
2. Press the OK / zoom button (10) to go into the
sub-menu.
3. Press the up (6) or down (8) navigation button
to select the camera you want to see (camera 1,
camera 2).
4. Press the OK / zoom button (10) to go to the
selected camera.
Note: The additional baby monitor reference
compatible with this additional camera is 89505
digimonitor 3.5" easy.
5.2.7. SCAN MODE
This function automatically cycles through your paired
camera channels to display each camera for 12 seconds.
This function can be used only when you have more
than 1 camera unit paired. To enter in this mode:
1. Press the menu button (5) to display the menu and
show the highlighted camera icon.
2. Press the OK / zoom button (10) to go into the
sub-menu.
3. Press the up (6) or down (8) navigation button until
the scan mode icon is highlighted.
12