Publicidad
Idiomas disponibles
Idiomas disponibles
2. Connect the adaptor to the mains.
When charging:
3. When the battery is charging and if the unit is
switched on, the LED indicator (X) will flash for five
seconds to indicate that the camera battery is charging.
While the camera is charging the LED indicator will
remain off and you can check the state of the battery
on the monitor screen (B).
4. When the battery is fully charged, the camera
charging indicator (B) on the monitor will stop flashing.
Note: If the camera is switched off the LED indicator
(X) will stay on until the charging cycle has been
completed.
Warning: Choking hazard – Keep the cord out of the
baby's reach. NEVER place a camera with cables less
than 1 meter from the cot. Never use extension cords
with AC adapters. Use only the AC adapters supplied.
5.2. OPERATION
5.2.1. TURNING THE CAMERA ON/OFF
To turn the camera on or off, keep the power button
(I) pressed in for two seconds.
The nightlight (VI) will come on for two seconds when
the unit is switched on and flash twice when the unit
is switched off.
When you have installed the camera and turned it
on, you can see the images and listen to the sounds
captured in your baby's room via the monitor.
5.2.2. PAN & TILT
This camera can be angled from the monitor by pressing
the left (9), right (7), up (6) or down (8) navigation
button until you find the desired viewpoint. Do not try to
move the camera or the lens (III) manually.
The camera has 355º lateral vision and 53º vertical
vision. It is important not to force the motor when it
reaches the maximum vision in one direction.
5.2.3. INFRARED NIGHT VISION (AUTOMATIC)
The infrared night vision function allows the camera to
pick up images in dark or low light conditions. In this
mode, only black and white images will be displayed
on the monitor and only objects located less than 2
meters away can be seen.
The camera automatically changes to infrared mode
when there is insufficient light for normal vision.
When the camera is in this mode, the night vision icon
(F) will be displayed on screen.
Note: The light sensor (II) is located at the top of
the camera. Take care not to cover the sensor with
any object to prevent the camera from entering night
mode when there is light in the room.
5.2.4. ADD CAMERA AND PAIRING
The device is designed to allow different areas to be
observed with up to two cameras. To pair the camera
follow the steps described below:
1. Press the menu button (5) to display the menu and
show the highlighted camera icon.
2. Press the down (8) navigation button until the add
/ remove icon is displayed and press the OK / zoom
button (10) to go into the sub-menu.
3. Press the up (6) or down (8) navigation button to
select the camera you want to add.
4. Press the OK / zoom button (10) to search for a
camera unit.
5. Press the pairing button on the camera (IX) for
5 seconds.
6. Once paired the image of the camera will show
immediately on the monitor unit screen.
For various reasons you may lose the connection
between the monitor and a camera which is already
connected. Should this be the case, repeat the process
explained above to connect the camera with the
monitor again.
Note 1: Before starting the pairing procedure, make
sure the camera and the monitor are close to one
another and that the camera is correctly plugged in
or has sufficient battery and is switched on.
Note 2: Each camera can be linked just with one
monitor at a time.
Nota 3: If the monitor and the camera, for some
reason, have left the factory without being paired,
you will have to do it manually adding the camera
to channel 2. You won't be able to pair the camera
again with channel 1 until you have paired it in
another channel and remove the channel 1 camera.
5.2.5. DELETE CAMERA
To delete one of the cameras connected, follow the
next steps:
1. Press the menu button (5) to display the menu and
show the highlighted camera icon.
2. Press the up (6) or down (8) navigation button
until the add / remove icon is displayed and then press
the OK / zoom button (10) to go into the sub-menu.
3. Press the up (6) or down (8) navigation button to
select the camera you want to remove and then press
the OK / zoom button (10) again.
Note: A channel needs to be deleted before pairing
to a new camera unit.
5.2.6. CHOOSING THE CAMERA
The device is designed to allow different areas to be
monitored with up to two cameras.
To select the camera you want to view, follow the steps
described below:
1. Press the menu button (5) to display the menu and
13
ENGLISH
Publicidad
