Publicidad
Idiomas disponibles
Idiomas disponibles
GETTING TO KNOW YOUR CLEANER
A.
Accessory Door
B.
Main Cleaner
C. Bag Door
D. Mechanical Bag Check Indicator*
E.
On/Off Pedal
F.
Exhaust Filter Cover
G. Cord Reel Pedal
H. Variable Power Control Slider**
H1. LED Display Screen with Variable Power Controls** and Led Bag Check Indicator*
I.
Carry Handle
J.
Bag Door Release Latch
K.
Hose
L.
Hose Handle**
M. Suction Regulator*
N. Telescopic Tube**
N
. Telescopic Tube Latch*
a
N
. Telescopic Tube Adjuster**
b
O. Carpet and Floor Nozzle (Gp)**
O1. Carpet Nozzle (Ca)*
O2. Hard Floor Nozzle (Hf)*
P.
Carpet and Floor Nozzle Slider*
Q. Floor Type Selector Pedal*
R. Carpet and Floor Nozzle Latch*
Sa. Pre-Motor Filter
Sb. Pre-Motor Filter Frame
T.
Exhaust Filter
U. Bag Holder
V.
Bag
W. Accessory Set
W1. Crevice Tool
W2. Furniture Nozzle
W3. Dusting Brush
X.
Pet Hair Remover Mini Turbo Nozzle*
Y.
Allergen Remover Mini Turbo Nozzle*
Z.
Parquet Nozzle*
ASSEMBLING YOUR CLEANER
Remove all components from the packaging.
1.
Connect the hose to the cleaner main body, ensuring it clips and locks into position.
To release the hose: simply press the two latches on the hose end and pull. [1]
*Certain Models Only
** May vary according to model
2.
Connect the hose handle to the upper tube end. [2]
3.
Connect the tube lower end to the carpet and floor nozzle** or accessories if required. [3]
USING YOUR CLEANER
1.
Extract power cord and plug it into the power supply. Do not pull the cord beyond the
red marker. [6]
2.
Adjust the telescopic tube to the desired height by moving the telescopic tube adjuster**
and raise or lower the tube to the most comfortable cleaning position. [5]
3.
After connecting the telescopic tube lower end to Carpet and Floor Nozzle** or
accessories if required, press the floor type selector* pedal on the nozzle to select
the ideal cleaning mode for the floor type.
Hard Floor – Brushes are lowered to protect the floor.
Carpet – Brushes are raised for deeper cleaning.
Carpet & Floor Nozzle**: [4]
-
Hard floor Cleaning: Press the pedal on the nozzle on Hard Floor mode and adjust
the slider on the nozzle on ALL FLOORS. In this position brushes, wheels and wiper
blade are lowered to protect hard floors. [4a]
-
Standard Carpet & Rugs Cleaning: Press the pedal on the nozzle on Carpet mode
and adjust the slider on the nozzle on ALL FLOORS. In this position brushes and
wiper blade are raised while wheels are lowered to allow a perfect ease of movement
on such surfaces. [4b]
-
Deep Carpet Cleaning: Press the pedal on the nozzle on Carpet mode and adjust the
slider on the nozzle on DEEP CARPET CLEANING. In this position brushes, wheels
and wiper blade are raised for a deeper cleaning of your carpet. [4c]
WARNING: It is recommended to avoid potential scratching of wooden floors that
the pedal is not set on hard floor mode and the slider on deep carpet cleaning.
4.
Switch the cleaner on by pressing the On/Off Pedal on the cleaner main body. [7]
5.
Adjust the power level by pressing the variable power control buttons on the
display** [8] or by adjusting the variable power control slider**. [9]
Adjust the suction regulator to the desired level. [10]
6.
7.
Switch off at the end of use by pressing the On/Off Pedal. Unplug and extract power
cord again to wind the power cord back into the cleaner.
8.
Parking and Storage - The tube can be parked for temporary storage while in use, or
in the storage position when not in use. [11]
ACCESSORIES
To obtain the best performance and efficiency it is recommended that the correct nozzles
are used for the main cleaning operations. These nozzles are indicated in the diagrams
by the letters GP, HF or CA.
A nozzle type GP can be used to clean both carpet and hard floor.
2
GB
Publicidad
