Publicidad
Idiomas disponibles
Idiomas disponibles
• Next, connect one end of the drainage hose using the rubber
GB
drainage cuff to the rear of the appliance. Attach the other
end to the sewage outlet / water container. The height of the
sewage outlet / water container must be situated lower than
the appliance, so that water can flow out.
Note: The inlet water supply pressure range: 1-8 kg/cm
0.785 MPa). Pressure reducer should be installed if the pres-
sure over this range.
Operating instructions
• Before first use, clean the appliance interior and exterior sur-
face with lukewarm water and a soft cloth.
• Position the appliance in a well-ventilated place, leaving at
least 150 mm gap around all sides for ventilation purposes.
• Let the appliance stand alone for about one hour in order to
settle the refrigerant. Make sure connect properly with the
water supply system.
• Then, plug in to a suitable socket.
• Press down the ON / OFF switch on the control panel in order
start up.
• Then, the appliance will use water to clean up inside and wa-
ter will flow out automatically. This time, light indicators of
"Operation indicator", "Display of fault", "Water level is too
low" are lights up and blink for about 30 seconds.
• Also, the ON / OFF switch lights up in green. The appliance
starts to operate.
• The flake ice making process is completely automatic, it con-
sists of several stages as below:
Water inlet ==> flake ice production ==> ejection of flake ice
==> storage of flake ice.
Then, push the slide door and use ice scoop to take out the ice.
• When the ice storage container is full, the "Storage tank is
full" indicator will light up in yellow and the appliance will
stop operation automatically.
• Once the flake ice have been removed, the appliance continue
production of flake ice automatically.
• Note: For sanitary reasons, you should dispose of the flake
ice produced in the first cycle for every use. Do not use them
for beverages or cooling food.
• If the water supply is insufficient, the "Water level is too low"
indicator will light up in yellow and the appliance will stop op-
erate automatically. Check the water supply (hose) connected
to the appliance.
• If any error or failure occur, the "Display of fault" indicator
will light up in red and the appliance will stop operation au-
tomatically.
• Switch OFF the appliance by pressing down the ON / OFF
switch and unplug it from the electrical supply when not in
use.
Notes:
• DO NOT switch ON again the appliance immediately after
shut down automatically (caused by insufficient water supply,
flake ice container too full, current interruption). Wait at least
3 ~ 5 minutes in order to avoid damages to the compressor.
• Check the connectors of the water inlet and outlet hose regu-
larly for the leakage or overflow of water that may be present.
• If the appliance is not used for a long period of time, screw off
the drainage cover at the rear of the appliance. Wipe dry the
water tank using a dry, clean cloth.
10
Cleaning & maintenance
• ATTENTION! Always disconnect the appliance from the pow-
er supply and cool down before storage, cleaning & mainte-
nance.
• Do not use water jet or steam cleaner for cleaning and do not
(0.098-
2
push the appliance under the water as the parts will get wet
and electric shock might be resulted.
• If the appliance is not kept in a good state of cleanliness, this
can adversely affect the life of the appliance and result in a
dangerous situation.
Cleaning
• Clean the cooled exterior surface with a cloth or sponge
slightly dampened with a mild soap solution.
• For reasons of hygiene, the appliance should be cleaned be-
fore and after use.
• Avoid water contacting the electrical components.
• Clean the inside of container with a non-abrasive detergent
and rinse with clean water.
• Never immerse the appliance in water or other liquids.
• Never use aggressive cleaning agents, abrasive sponges, or
cleaning agents containing chlorine. Do not use steel wool,
metallic utensils, or any sharp or pointed objects for clean-
ing. Do not use petrol or solvents!
• No parts are dishwasher safe.
• Clean the condenser for every 2 ~ 3 months.
Maintenance
• Check the operation of the appliance regularly to prevent se-
rious accidents.
• If you see that the appliance is not working properly or that
there is a problem, stop using it, switch it off and contact the
supplier.
• All maintenance, installation and repair work must be car-
ried out by specialised and authorised technicians, or recom-
mended by the manufacturer.
Transportation and Storage
• Before storage, always make sure that the appliance has
been disconnected from the power supply and completely
cooled down.
• Store the appliance in a cool, clean and dry place.
• Never place heavy objects on the appliance as this could
damage it.
• Do not move the appliance while it is under operation. Dis-
connect the appliance from power supply when moving and
hold it at the bottom.
• Special care must be taken when moving or transporting the
machine due to its heavy weight. With at least 2 persons or
using a cart. Move the machine slowly, carefully, and never
incline more than 45°.
Publicidad
