Publicidad
Idiomas disponibles
Idiomas disponibles
the appliance is moved afterwards.
• If the appliance has been switched off or disconnected from
the power supply, it is necessary to wait 5 minutes until
switching on again.
• No other appliances should be plugged into the same socket
as with this appliance.
Intended use
• This appliance is intended to be used in household and simi-
lar applications such as:
- staff kitchen areas in shops, offices and others working en-
vironment;
- farm houses;
- by clients in hotels, motels and other residential type en-
vironment;
- bed and breakfast type environment.
• The appliance is designed for making flake ice continuously.
Any other use may lead to damage of the appliance or per-
sonal injury.
• Operating the appliance for any other purpose shall be
deemed a misuse of the device. The user shall be solely liable
for improper use of the device.
Grounding installation
This appliance is classified as protection class I and must be
connected to a protective ground. Grounding reduces the risk
of electric shock by providing an escape wire for the electric
current.
This appliance is fitted with a power cord with grounding plug
or electrical connections with grounding wire. The connections
must be properly installed and grounded.
Main parts of the product
(Fig.1 on page 3)
1. ON / OFF switch with built-in indicator (Green)
2. Display panel showing different function lamp
3. Front panel
4. Sliding door
5. Ice shelf
6. Ice storage container
7. Ice capacity sensor
8. Power cord
9. Water supply inlet
10. Drainage tube hole
11. Feet
12. Drainage cover
13. Power cord
Remark: The content of this manual applies for all listed items
unless specified otherwise. The appearance may vary from the
shown illustrations.
Spare parts or accessories
(Fig.2 on page 3)
14. Water inlet supply hose
15. Water drainage hose
16. Spare sealing washer x2
17. Ice scoop
Control panel
(Fig.3 on page 4)
1. Operation indicator (Green)
2. Display of fault (Red)
3. Storage tank is full (Yellow)
4. Water level is too low (Yellow)
Preparation before use
• Remove all protective packaging and wrapping.
• Check that the device is in good condition and with all ac-
cessories. In case of incomplete or damaged delivery, please
contact the supplier immediately. In this case, do not use the
device.
• Clean the accessories and the appliance before use (See ==>
Cleaning & Maintenance).
• Make sure the appliance is completely dry.
• Place the appliance on a horizontal, stable and heat resistant
surface that is safe against water splashes.
• Keep the packaging if you intend to store your appliance in
the future.
• Keep the user manual for future reference.
NOTE! Due to manufacturing residues, the appliance may emit
a light odor during the first few uses. This is normal and does
not indicate any defect or hazard. Make sure the appliance is
well ventilated.
Installation
Attention: Any installation, maintenance and repair work
should be performed by qualified and authorized technician
only.
• Check to make sure that the appliance is undamaged or com-
plete delivery. In case of any damage or incomplete delivery,
DO NOT use the appliance and contact the supplier imme-
diately.
• Check that the accessories such as water supply hose, wa-
ter drainage hose, 2 spare sealing washers & ice scoop are
included.
• Remove all packing material and protective film (if applica-
ble).
• Place the appliance on a level, steady and safe surface which
can supports the weight of the appliance together with the
flake ice produced during use.
• Avoid expose to direct sunlight or direct source of heat such
as cooker, heat oven, etc.
• Make sure that a minimum of 20 cm distance is kept around
all sides of the appliance for ventilation purposes.
• Place the appliance in such a way that the plug is easily ac-
cessible and can be quickly removed from its socket in case
of necessity.
• Set up the appliance near water supply connection.
Connection to the water supply
(Fig 1 on page 3)
Attention: The appliance should be connected to a cold drink-
able water supply only. Otherwise, a cleaning system or filter
should be installed in advance.
• Connect one end of the water inlet supply hose to the 3 / 4"
screw type connector of the water tap supply so as to get the
drinkable tap water. Then, connect the other end of this hose
to the back of the appliance by screwing clockwise. Be sure to
put sealing washers in both ends before connecting.
GB
9
Publicidad
