Attwood 5610-48-7 Instrucciones Para La Instalación

TELESCOPING ALL-ROUND POLE LIGHT
5610-48-7
INSTALLATION INSTRUCTIONS
SAVE THESE INSTRUCTIONS
PRODUCT FEATURES
Light meets USCG CFR 183.810, ABYC A-16 requirements, and all applicable
standards as tested by Immana Labs, 8/4/2009. 2 Nautical Mile visibility. Use
Attwood Lamp #9233, #1004 12-Watt.
CAUTION:
Read all instructions carefully before installing and using this product. All positive
(+12V DC) lighting wires require a 1-amp fuse to protect circuits and vessel. The
aluminum light pole is not grounded. MAKE SURE POWER SOURCE IS 12-VOLT
DC ONLY. HIGHER VOLTAGE WILL DAMAGE LIGHT AND CIRCUITRY.
WARNING:
To prevent injury, disconnect power when installing or servicing this product.
Remove boat from water before using 120V power tools.
LOCATION
The Telescoping All-Round Pole Light is designed for boats up to 39.4 feet
(12m). Position the All-Round Light so its bulb is not less than one meter
(39.4") above navigation bow lights when extended. If replacing an existing
pole light, replace with a pole at least as long as the existing. Mount the light in
a position that will allow the light to shine 360°, unobstructed. (See Figure 1)
Figure 1 | Figura 1
One meter
or 39-3/8"
INSTALLATION
1. Remove pole light from stowaway
compartment and loosen thumb
screw. (See Figure 2)
2. Grab onto aluminum pole section
and pull/extend the telescoping
section to a height that places
the All-Round Light 39.4" (1m)
above the navigation bow lights.
3. Hand-tighten the thumb screw.
4. Insert extended pole light into
light base and secure.
5. Turn power to light on and
verify function.
REPLACING LIGHT POLES WITHOUT A LOCKING COLLAR
1. Align pole screws with slot in the existing base. Insert pole into
base (Figure 3).
2. Press down fi rmly to engage electrical connectors.
3. To remove pole, pull straight up.
TO CONVERT POLE FOR USE WITHOUT A LOCKING COLLAR
1. For bases that do not accept locking collar, remove both screws
at bottom of pole. Slide locking collar off end of pole.
2. Replace screws in pole.
08/10 69475 Rev. A
Figure 2 | Figura 2
Figure 3
Figura 3
911339
REPLACING LIGHT POLES WITH LOCKING COLLAR (5110 SERIES)
1. Remove upper pole screw from base of pole. (Figure 4)
2. Align pole screw with slot in the base. Insert pole into base.
3. Press down fi rmly to engage electrical connectors.
4. Slide locking collar down to base, rotate until you can insert lower ring
inside top of base.
5. Press collar down into base and rotate until it tightens between
pole and base.
NOTE: Periodically check pole to make sure it is secure.
6. To remove light, rotate locking collar in opposite direction until
then pull up on pole.
Figure 4
Figura 4
Locking Collar
Bague de blocage
Abrazadera de cierre
Lower Ring
Anneau inférieur
Anillo inferior
Upper Screw
(remove)
Vis supérieure (retirer)
Tornillo superior (extraer)
Lower Screw
Vis inférieure
Tornillo inferior
OPERATION
After installation, check lights to verify proper operation. Regulations
require lights to be operated with a three-position switch for:
• Running lights (sidelights and all-round light)
• Anchor lights (all-round light only)
• Off
NOTE: Do not use light pole as a fl agpole or handle.
MAINTENANCE
When not in use, store pole light in Pole Light Storage Clips (Attwood 7571).
Choose a storage location where light will not be damaged or be in constant
contact with water.
REPLACING BULB
1. Unscrew frosted globe counter-clockwise and remove.
2. Replace with #1004 12-Watt Wedge Base Replacement Bulb (Attwood
#9233) available in marine, auto, and convenience stores.
3. Screw lens clockwise onto pole.
Clean the light with a mild soap and warm water solution. Never use solvents
or abrasives that may damage the lens or housing of the light.
ATTWOOD LIMITED WARRANTY
This product carries a one (1) year warranty. See product catalog or www.
attwoodmarine.com for details.
©2010 Attwood Corporation • 1016 N. Monroe Street,
Lowell, MI 49331-0260 • www.attwoodmarine.com
911370, or 911445 91041 - 91048
91020, 91024
or 91026
it loosens,
91022