Descargar Imprimir esta página

Qilive Q.6152 Manual Del Usuario página 13

Secadora con bomba de calor de 8 kg

Publicidad

Idiomas disponibles

Idiomas disponibles

6.2.3
Clean the lint filter
1.
Open the door.
2.
Take out the lint filter.
3.
Open the filter and remove the lint. Rinse it with water, if necessary.
4.
Dry the filter thoroughly before reinstalling.
Note:
The lint accumulated on the filter will block the air circulation, which will cause the extension of drying
time and increase energy consumption. Therefore the lint filter shall be cleaned after each use.
Take notice of the correct orientation before inserting the lint filter.
Do not operate the dryer without the lint filter!
Clean the lint filter after each use to prevent lint accumulation inside the dryer.
6.2.4
Clean the base filter
1.
Open the cover.
2.
Unlock three locking levers and grasp the filter handle.
3.
Remove the base filter and clean it. If there is too much lint on the filter, clean it in water. Dry the filter
thoroughly before installing it back.
4.
Clean the rubber sealing, both at the filter and handle.
5.
Re-insert the filter.
6.
Lock three locking levers and make sure that the levers are incorrect lock position.
7.
Close the cover until there is a click sound.
Note:
The lint accumulated on the filter will block the air circulation. Not cleaning the filter regularly will
increase drying time and energy consumption.
Disconnect the power cord before cleaning!
Do not operate the dryer without the filter!
Clean the base filter after each fifth cycle to prevent lint accumulation inside the dryer.
6.2.5
Cabinet and drum cleaning
WARNING: Disconnect the tumble dryer from the mains electricity supply before cleaning.
Clean the housing, control panel, door seal and the door, especially the inside window with a slightly damp cloth. After cleaning,
dry all parts with a soft cloth.
Clean the humidity sensor inside the drum.
Take out all the filters, clean the sealing and air flow openings.
Do not use solvents, abrasive cleaners, glass cleaners, or all-purpose cleaners. These could damage plastic surfaces and other
parts.
The tumble dryer must never be hosed down.
Please wear gloves when cleaning.
Before starting the dryer, dry all parts with a soft cloth
7. TROUBLESHOOTING
With the help of the following notes minor faults in the performance of the appliance, some of which may result from incorrect
operation, can be put right without contacting the Service Centre.
Repair work to electrical appliances should only be carried out by a suitably qualified person in strict accordance with current local
and national safety regulations. Repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be
held liable for unauthorized work.
Display
"E32"
"E33"
"E82"
WARNING:
Only authorized technicians can carry out repairs.
If the LED displays another prompt and the tumble dryer does not work, please call the service.
Note: Before calling the service centre, check the user manual to see if you can solve the problem yourself.
Problem
Display is not on.
" " is lighting.
" " is lighting.
The tumble dryer does not
start.
Degree of dryness was not
reached or drying time too
long.
There are humming noises.
The dryer switches off at the
end of the programme.
WARNING: If you cannot deal with the problems by yourself and need help:
Press the
On/Off button. Then, pull out the mains plug and call the service.
Possible cause
Humidity sensor error
Temperature sensor error
Communication error
Check if the power supply works.
Check if the mains plug is inserted.
Empty water container.
If the container is not full, restart the dryer.
Clean the lint filter.
Wait for the power to be restored.
Check the power socket and make sure the
plug is firmly inserted.
Turn on the tumble dryer.
Clean lint filter and heat exchanger.
Empty the water container.
Check the drain hose.
The compressor is operating. These noises are quite normal and do not indicate a fault.
The tumble dryer switches off automatically for energy saving. This is not an error but a normal
function.
If the problem persist, contact your local
service centre.
Remedy
Check the selected programme .
Press the
If the light still remains on, please call the
service centre.
Check whether the door is closed properly.
Check whether the programme is set.
Press the
Check installation place is appropriate.
Keep the air inlet clean.
Use a higher drying intensity level programme
or time programme.
13 13
Lint filter
Remedy
On/Off button.
Start/Pause button.
EN

Publicidad

loading