Specific Safety Rules; Battery Installation - BLACK&DECKER EasyEdge BDPE200-LA Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

FEATURES (Fig. A)
1. Main Body
2. On/Off Trigger
3. Flow Control Knob
4. Battery Cap
5. Battery Cap Release Tabs
6. Paint Applicator*
7. Paint Applicator Release Tabs
8. Paint Tube*
9. Plunger*
10. Plunger Drive
11. Fill Sleeve
12. Fill Sleeve Locking Tabs
13. Fill Sleeve Paint Can Clips
*Applicator head, Paint tube, Plunger are made of Acetyl, ABS,
Polypropylene and Poly Ethylene. Please ensure your local recycling
agencies can recycle these materials together. Parts must be washed
before being recycled.

SPECIFIC SAFETY RULES

f Do not use this paint edger for purposes other than
described in this manual. Failure to do so may result in
injury to persons and or property damage.
f keep hands out of the plunger drive area of the
paint edger. Fingers can be pinched between the
plunger drive and the plunger.
f Use only with water soluble based paints. Not for use
with oil based paints and stains (refer to label on original
paint container). Do not use with paint removers, solvents, or
the like. Liquids other than paint may damage product and
result in injury to persons or property damage.
f Always read and follow the label on the original paint
container and follow all directions. Failure to do so may
result in injury to persons or property damage.
f Always use proper eye protection and other safety
equipment for skin and respiratory protection when
mixing the paint, and when filling, using, and cleaning
the product. Paint and its fumes can cause personal injury.
f To reduce the risk of injury, always work in a
properly ventilated area and wear appropriate
respiratory protection if necessary. Fumes from
some paints can be noxious.
f Thoroughly clean and rinse product after using with
a particular paint. Mixing different paints in the product
may cause personal injury and or result in property damage.
f To reduce the risk of injury, use only recommended
accessories.
f When servicing, use only identical replacement
parts. Failure to do so may result in personal injury.
ASSEMBLY

BATTERY INSTALLATION

Warning! Batteries can explode, or leak, and can
cause injury or fire.
To reduce this risk:
f Carefully follow all instructions and warnings on the
battery label and package.
f Always insert batteries correctly with regard to polarity
(+ and -), marked on the battery and the equipment.
f Do not short battery terminals.
f Do not charge batteries.
f Do not mix old and new batteries. Replace all of them
at the same time with new batteries of the same brand
and type.
f Remove dead batteries immediately and dispose of
per local codes.
f Do not dispose of batteries in fire.
f Keep batteries out of reach of children.
f Remove batteries if the device will not be used for
several months.
"Transporting batteries can possibly cause fires if
the battery terminals inadvertently come in contact with
conductive materials such as keys, coins, hand tools and
the like. The US Department of Transportation
Hazardous Material Regulations (HMR) actually prohibit
transporting batteries in commerce or on airplanes (i.e.
packed in suitcases and carryon luggage) UNLESS
they are properly protected from short circuits. So when
transporting individual batteries, make sure that the
battery terminals are protected and well insulated from
materials that could contact them and cause a short
circuit".
f Remove the battery cap (4) by pressing in the battery
release tabs (5) and then sliding the battery cap (4) off
the handle.
f Insert 3 fresh 1.5 volt AA batteries into the handle as
shown in Figure B.
f Refit the battery cap (4) by sliding it back on to the
handle until it is firmly seated.
Note: Always place batteries correctly according to
the polarity (+ and -) as marked on the battery and the
tool.
Installing the paint applicator (Fig. C)
f Press in the paint applicator release tabs (7).
f Slide the paint applicator (6) into the front of the main
body (1) of the paint edger until it is firmly seated.
f Release the tabs.
Note: The paint applicator (6) can not be fitted with
the paint tube in place.
Removing the paint applicator
f Press in the paint applicator release tabs (7).
f Slide the paint applicator out of the main body (1) of
the paint edger.
ENGLISh • 17

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Easyedge bdpe200-ar

Tabla de contenido