Bosch Professional GST 700 Manual Original página 21

OBJ_BUCH-3179-003.book Page 21 Wednesday, August 9, 2017 4:33 PM
Switching On and Off
To switch on the power tool, press the On/Off switch 2 and
keep it pressed.
To lock the pressed On/Off switch 2, push the lock-on button
1 toward the right or left.
To switch off the machine, release the On/Off switch 2. When
the On/Off switch 2 is locked, press it first and then release it.
Working Advice
 Before any work on the machine itself, pull the mains
plug.
 When working small or thin work pieces, always use a
sturdy support or a saw table (accessory).
Check wood, press boards, building materials, etc. for foreign
objects such as nails, screws or similar, and remove them, if
required.
Plunge Cutting (see figure D)
 The plunge cutting procedure is only suitable for treat-
ing soft materials such as wood, plaster board or simi-
lar! Do not work metal materials with the plunge cut-
ting procedure!
Use only short saw blades for plunge cutting. Plunge cutting is
possible only with the mitre angle set at 0°.
Place the machine with the front edge of the base plate 6 on
to the workpiece without the saw blade 10 touching the work-
piece and switch on. For machines with stroke rate control,
select the maximum stroke rate. Firmly hold the machine
against the workpiece and by tilting the machine, slowly
plunge the saw blade into the workpiece.
When the base plate 6 fully lays on the workpiece, continue
sawing along the desired cutting line.
Parallel Guide with Circle Cutter (Accessory)
For cuts using the parallel guide with circle cutter 19 (acces-
sory), the thickness of the material must not exceed a maxi-
mum of 30 mm.
Parallel Cuts (see figure E): Loosen the locking screw 18 and
slide the scale of the parallel guide through the lead 17 in the
base plate. Set the desired cutting width as the scale value on
the inside edge of the base plate. Tighten the locking screw 18.
Circular Cuts (see figure F): Set the locking screw 18 to the
other side of the parallel guide. Slide the scale of the parallel
guide through the lead 17 in the base plate. Drill a hole in the
workpiece centred in the section to be sawn. Insert the cen-
tring tip 20 through the inside opening of the parallel guide and
into the drilled hole. Set the radius as the scale value on the in-
side edge of the base plate. Tighten the locking screw 18.
Coolant/Lubricant
When sawing metal, coolant/lubricant should be applied
alongside cutting line because of the material heating up.
Bosch Power Tools
Maintenance and Service
Maintenance and Cleaning
 For safe and proper working, always keep the machine
and ventilation slots clean.
Clean the saw blade holder regularly. For this, remove the saw
blade from the machine and lightly tap out the machine on a
level surface.
Heavy contamination of the machine can lead to malfunc-
tions. Therefore, do not saw materials that produce a lot of
dust from below or overhead.
 In extreme conditions, always use dust extraction as
far as possible. Blow out ventilation slots frequently
and install a portable residual current device (PRCD).
When working metals, conductive dust can settle in the in-
terior of the power tool. The total insulation of the power
tool can be impaired.
Lubricate the guide roller 9 occasionally with a drop of oil.
Check the guide roller 9 regularly. If worn, it must be replaced
through an authorised Bosch after-sales service agent.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the nameplate of
the product.
Disposal
The machine, accessories and packaging should be sorted for
environmental-friendly recycling.
Do not dispose of power tools into household
waste!
Subject to change without notice.
English | 21
1 609 92A 3W8 | (9.8.17)