Descargar Imprimir esta página

EINHELL TE-AC 430/90/10 Manual De Instrucciones Original página 16

Ocultar thumbs Ver también para TE-AC 430/90/10:

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 84
Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.
Explanation of the symbols used (see Fig. 16)
1. Warning - Read the operating instructions to
reduce the risk of inquiry.
2. Warning! Wear ear-muff s. The impact of
noise can cause damage to hearing.
3. Warning of electrical voltage!
4. Warning of hot parts!
5. Warning! The unit will start up automatically
without warning if the pressure drops below
cut-in pressure!
6. Notice! Before using for the fi rst time, check
the oil level and replace the oil sealing plug!
7. Overload switch
1. Safety regulations
The corresponding safety information can be
found in the enclosed booklet.
Danger!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, fi re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
This appliance is not intended for use by persons
(including children) with reduced physical, sen-
sory or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
2. Layout and items supplied
2.1 Layout (Fig. 1-4)
1. Intake air fi lter
2. Pressure tank
Anl_TE_AC_430_90_10_SPK13.indb 16
Anl_TE_AC_430_90_10_SPK13.indb 16
GB
3. Wheel
4. Guide roller
5. Quick-lock coupling (regulated compressed
air)
6. Pressure gauge (for reading the set pressure)
7. Pressure regulator
8. On/Off switch
9. Transport handle
10. Safety valve
11. Drainage cock for condensation water
12. Pressure gauge (for reading the vessel pres-
sure)
13. Quick-lock coupling (unregulated com-
pressed air)
14. Oil sealing plug
15. Oil drainage screw
16. Overload switch
17. Oil fi ller opening
18. Wheel cap
19. Screw (internal hexagon) for fi tting the handle
20. Hexagon key
21. Safety guard for V-belt
22. Washer
23. Nut for fi tting the castors
24. Axle screw
25. Spring washer
26. Nut for fi tting the axle
27. Castor brake
28. Non-return valve
29. Oil level window
2.2 Items supplied
Please check that the article is complete as spe-
cifi ed in the scope of delivery. If parts are missing,
please contact our service center or the nearest
branch of the DIY store where you made your
purchase at the latest within 5 work days after
purchasing the article and upon presentation of
a valid bill of purchase. Also, refer to the warranty
table in the warranty provisions at the end of the
operating instructions.
Open the packaging and take out the equip-
ment with care.
Remove the packaging material and any
packaging and/or transportation braces (if
available).
Check to see if all items are supplied.
Inspect the equipment and accessories for
transport damage.
If possible, please keep the packaging until
the end of the guarantee period.
- 16 -
02.08.2023 11:29:09
02.08.2023 11:29:09

Publicidad

loading

Este manual también es adecuado para:

40.108.00