Briteq LD-Power 60 Manual De Instrucciones página 8

ENGLISH
 Use DOWN and UP buttons browse the different options:
 For each option you can press ENTER, follow by the UP/DOWN buttons to set the desired level.
Each time confirm with the ENTER button.

or (red for zone 1 on LD-POWER120)

or (green for zone 1 on LD-POWER120)

or (blue for zone 1 on LD-POWER120)

or (white for zone 1 on LD-POWER120)

(red for zone 2 on LD-POWER120)

(green for zone 2 on LD-POWER120)

(blue for zone 2 on LD-POWER120)

(white for zone 2 on LD-POWER120)

(Overall dimmer level)

(overall strobe speed: values correspond to the strobe channel on the DMX chart)
 After testing, just press the MENU button for about 2 seconds to return to running mode.
Adjust White balance
Makes it possible to adjust the white color when all colors are at maximum.
 Press the MENU button until
is shown on the display.
 Press the ENTER button to select: all connected projectors turn to white color (all colors at maximum,
except for white) while the display shows
 Use DOWN and UP buttons browse the different options:
 For each option you can press ENTER, follow by the UP/DOWN buttons to set the desired level.
Each time confirm with the ENTER button.

or (red for zone 1 on LD-POWER120)

or (green for zone 1 on LD-POWER120)

or (blue for zone 1 on LD-POWER120)

(red for zone 2 on LD-POWER120)

(green for zone 2 on LD-POWER120)

(blue for zone 2 on LD-POWER120)
 Press the MENU button for about 2 seconds to save the setting and return to running mode, press shortly
to return without saving.
Remark: You can only set values between 125 and 255.
Self-Test
 Press the MENU button until
is blinking on the display.
 Press the ENTER button: the unit will run the built-in programmer for self-test.
 Press the MENU button for about 2 seconds to return to running mode.
Led Display
Display on: display is always on.
Display off: display is off when not used.
 Press the MENU button until the display shows
 Press the ENTER button.
 Use DOWN and UP buttons to select
(display always on) or
 Once the mode is selected, press the ENTER button.
(or automatically return to the main functions without any change after 8 seconds)
 Press the MENU button for about 2 seconds to save the setting and return to running mode, press shortly
to return without saving.
Fixture Hours
Used to show the number of working hours of the unit.
 Press the MENU button until
is shown on the display.
 Press the ENTER button to show the number of working hours in the display.
BRITEQ (LD-SERIES) 11/65
®
OPERATION MANUAL
(LD-POWER60) or (LD-POWER120)
.
(display off when not used).
LD-POWER60 / LD-POWER120
ENGLISH
 Press the MENU button for about 2 seconds to return to running mode.
Software version:
Used to show the software version of the unit.
 Press the MENU button until
is shown on the display.
 Press the ENTER button to show the software version of the unit.
 Press the MENU button for about 2 seconds to return to running mode.
SPECIFICATIONS
Power Input: 100Vac ~ 240Vac 50/60Hz.
Fuse (LD-POWER60): 250V 1A slow blow (20mm glass)
Fuse (LD-POWER120): 250V 2A slow blow (20mm glass)
Power output (LD-POWER60): 1x zone 60W = 60Watt
Power output (LD-POWER120): 2x zone 60W = 120Watt
Max LED load per zone (RGB + RGBW): max. 12 LEDs per color (total max. = 48pcs)
Max LED load per zone (WHITE MODE): 4 circuits, each supporting max. 12 LEDs (total max. = 48pcs)
DMX connections: 3pin XLR male / female
DMX channels used: 2 to max 11 channels (depends on working mode)
Size: see drawings
Weight (LD-POWER60): 1,2kg
Weight (LD-POWER60): 2,1kg
LD-POWER60
Every information is subject to change without prior notice
You can download the latest version of this user manual on our website: www.beglec.com
BRITEQ (LD-SERIES) 12/65
®
OPERATION MANUAL
LD-POWER120
LD-POWER60 / LD-POWER120