Publicidad
Idiomas disponibles
Idiomas disponibles
cord length a nd nameplate
amperage
rating. Ifindoubt, use the
next h eavier size line gauge. The smaller the gauge n umber, the
heavier the cord. Toprevent the cord from disconnecting
from
the unit, u se the cord hook s hown i nthe
Operating Instructions.
• A nameplate on your unit indicates the voltage used. Never
connect the unit to an AC voltage that differs from this voltage.
• Inspect all extension cords and the unit power connection
periodically. Look closely for deterioration, cuts or cracks in the
insulation. Also inspect the connections for damage. Repair or
replace the cords if any defects appear.
• Ground Fault Circuit Interrupter (GFCI) protection
should be
provided on the circuit(s) or outlet(s) that will be used for the
unit. Use receptacles with built-in GFCI protection for an
extra measure of safety.
OTHER SAFETY WARNINGS
• Inspect the unit before use. Replace damaged parts. Make
sure all fasteners are in place and secure. Replace cutting
attachment
parts that are cracked, chipped or damaged in
any way. Make sure the cutting attachment
is properly
installed and securely fastened. Be sure that the cutting
attachment shield is properly attached, and positioned as
recommended.
Failure to do so can result in personal injury to
the operator and bystanders, as well as damage to the unit.
• This unit was not designed to be used as a brushcutter. Do not
attach or operate this unit with any type of brushcutting blade or
brushcutting attachment. The use of any other accessory or
attachment may increase the risk of injury when used with this unit.
• Use only yellow Hassle Free IW MXTRA QUIET Spiral Line.
Never use metal-reinforced
line, wire, chain or rope. These can
break off and become dangerous projectiles.
• Be aware of risk of injury to the head, hands and feet.
• Be sure to secure the unit while transporting.
• Never douse or squirt the unit with water or any other liquid.
Keep handles dry, clean and free from debris. Clean after each
use. See the Cleaning and Storage instructions.
• Keep these instructions.
Refer to them often and use them to
instruct other users. If you loan someone this unit, also loan
them these instructions.
WHILE OPERATING
• The cutting attachment shield must always be in place while
operating the unit. Do not operate unit without both trimming
lines extended, and the proper line installed. Do not extend the
trimming line beyond the length of the shield.
• Adjust the D-handle to your size to provide the best grip.
• Be sure the cutting attachment
is not in contact with anything
before starting the unit.
• Use the unit only in daylight or good artificial light.
• Avoid accidental starting. Do not carry around a unit that is
plugged in with your finger on the trigger switch. Be sure the
switch is in the off position when plugging in the unit.
• Do not overreach. Always keep proper footing and balance.
• Always hold the unit with both hands when operating.
Keep a
firm grip on both handles or grips.
• Keep hands, face, and feet at a distance from all moving parts. Do
not touch or try to stop the cutting attachment when it rotates.
• Always stop the motor when cutting is delayed or when
walking from one cutting location to another.
• If you strike or become entangled with a foreign object, stop
the motor immediately and check for damage. Do not
operate before repairing damage. Do not operate the unit
with loose or damaged parts.
• Stop the unit and unplug it for maintenance or repair.
• Keep unit clean of vegetation and other materials. They may
become lodged between the cutting attachment
and shield.
• Do not force appliance-It will do the job better and with less
likelihood of a risk of injury at the rate for which if was designed.
SAVE THESE INSTRUCTIONS
• SAFETY & INTERNATIONAL
SYMBOLS •
This operator's
manual describes safety and international symbols and pictographs
that may appear on this product.
Read the
operator's
manual for complete safety, assembly, operating and maintenance and repair information.
SYMBOL
MEANING
• SAFETY ALERT SYMBOL
Indicates
danger, warning or Cautionl May be used
in conjunction with other symbols Or pictographs.
'
WARNING _ READ OPERATOR'S
MANUAL
_]]
I I1_
Read the operator's manual(s)and follow all wamings
and safety instructions. Failureto do so can result in
set OUSnjury to the operator and/or bystanders,
• WEAR EYE AND HEARING PROTECTION
WARNING:
Thrown objects and loud noise can
severe eye injury and hearing loss. Wear
!
eye protection meeting ANSI Z87.1 standards
and ear protection when operating this unit. Use
a full face shield when needed.
'THROTTLE
CONTROL
!ndicates
HIGW or FASTEST !pee d,
• THROTTLE
CONTROL
_qDLE," %OW," or "SLOWEST"
speed.
SYMBOL
MEANING
• KEEP BYSTANDERS AWAY
L_,,,,,_:,_
WARNING:
Keep all bystanders,
especially
_, _',_i_,
children and pets, at least 50 feet 115 m) from
_L.._...L(.JL
the operating area.
• THROWN OBJECTS AND ROTATING
CUTTER CAN CAUSE SEVERE INJURY
WARNING: Do not operate without the cutting
attachment
shield in place. Keep away from the
rotating cutting attachment.
•
DOUBLE INSULATED
Two systems of insulation
are erovided in stead of
grounding
There is no grounding
provided and no
means of grounding should be added to this unit.
_/_•
SHARP BLADE
WARNING:
Sharp blade on cutting attachment
shield. To prevent serious injury, do not touch
the line cutting blade.
,(l_0_
* BLOWERS
WARNING: Stop the motor and allow the
__Z¢(
impeller to stop and unplug before cleaning or
_
performing any maintenance.
Publicidad
