Publicidad
Idiomas disponibles
Idiomas disponibles
put excessive force on the saw, letting the saw
do its work. The motor will overload and can
FYVR SYX -X [MPP HS XLI NSF FIXXIV ERH WEJIV EX XLI
rate for which it was intended.
(6) Remove the saw from a cut with the saw running
EX JYPP WTIIH 7XST XLI WE[ F] VIPIEWMRK XLI 3R
off Trigger. Make sure the chain has stopped
before setting the saw down.
(7) Keep practicing on scrap logs in a secure
working area until you are comfortable, using a
YMH QSXMSR ERH E WXIEH] GYXXMRK VEXI
Kickback Safety Devices On This Saw
This saw has a low-kickback chain and reduced
kickback Guide Bar. Both items reduce the chance
of kickback. However, kickback can still occur with
this saw.
The following steps will reduce the risk of kickback.
•
Keep all safety items in place on saw. Make sure
they work properly.
•
Do not overreach or cut above shoulder height.
•
Keep solid footing and balance at all times.
•
Stand slightly to the left side of saw. This keeps
your body from being in direct line with chain.
•
Do not let Guide Bar nose touch anything when
chain is moving.
•
Never try cutting through two logs at same time.
Only cut one log at a time.
•
Do not bury the Guide Bar nose or try plunge cut
(boring into wood using Guide Bar nose).
•
Watch for shifting of wood or other forces that
may pinch chain.
•
Use extreme caution when reentering a previous
20
cut.
•
Use only the low-kickback chain and Guide Bar
that were supplied with this pruning saw or
recommended.
•
Never use a dull or loose chain. Keep chain
sharp with proper tension.
How to use Saw Safely
1. Use the pruning saw only with secure footing.
2. Hold the pruning saw at the right-hand side of
your body (See Fig. L).
3. The Chain must be running at full speed before it
makes contact with the wood.
4. Use the Base Plate to secure the saw onto the
wood before starting to cut.
5. Use the Base Plate as a leverage point while
cutting. (See Fig. M)
6. Do not operate the saw with arms fully extended,
EXXIQTX XS WE[ EVIEW [LMGL EVI HM GYPX XS VIEGL
or stand on a ladder while sawing. (See Fig. N)
Never use the pruning saw above shoulder height.
Cordless Pruning Saw
Cutting wood under tension (See Fig. O)
WARNING: When cutting a limb that is under
tension, use extreme caution. Be alert for wood
springing back. When wood tension is released, limb
could spring back and strike operator causing
severe injury or death.
When sawing logs supported on both ends, start the
GYX JVSQ EFSZI =
EFSYX SJ XLI HMEQIXIV MRXS
XLI PSK SZIVFYGO
ERH XLIR RMWL XLI GYX >
JVSQ
below, in order to avoid contact of the pruning saw
with the ground. When sawing logs supported on
SRP] SRI IRH WXEVX XLI GYX JVSQ FIPS[ =
EFSYX
SJ XLI HMEQIXIV MRXS XLI PSK YRHIVFYGO
ERH RMWL
the cut from above (Z) in order to avoid log splitting
SV NEQQMRK SJ XLI TVYRMRK WE[
OPERATION FOR POLE SAW
Cutting with extension pole
1. Install the battery pack into the machine.
2. Before cutting a high branch, consider all the
same points detailed in the previous section
"Trimming Branches" but pay particular
attention to the likely path of the falling branch.
WARNING: Do not stand directly below a branch
being cut. Keep bystanders far away. Do not stand
on a ladder or other type of unstable support while
using the tool. Do not use the tool near cable,
electrical power or telephone lines. Keep 3m away
from all power lines. (See Fig. P1-P4)
3. Use both hands to grip Pole Saw. Use only
designated grip areas when operating Pole Saw
7II *MK 4
9WI VQ KVMT 8LYQFW ERH RKIVW
must wrap around Pole Saw handle and pole.
1EOI WYVI ]SYV JSSXMRK MW VQ /IIT JIIX ETEVX
Divide your weight evenly on both feet.
5. When ready to make a cut, press the Lock-out
&YXXSR XLIR JYPP] TVIWW XLI 3RSJJ 8VMKKIV 7II
Fig. P6). This will turn Pole Saw on. Releasing
3RSJJ 8VMKKIV [MPP XYVR 4SPI 7E[ SJJ 1EOI WYVI
saw is running at full speed before starting a cut.
6. When starting a cut, place moving chain
EKEMRWX [SSH ,SPH 4SPI 7E[ VQP] MR TPEGI XS
avoid possible bouncing or skating (sideways
movement) of saw.
7. Guide Pole Saw using light pressure. Do not
force Pole Saw. The motor will overload and can
FYVR SYX -X [MPP HS XLI NSF FIXXIV ERH WEJIV EX XLI
rate for which it was intended.
8. Remove Pole Saw from a cut with saw running
at full speed. Stop Pole Saw by releasing trigger.
Make sure chain has stopped before setting
Pole Saw down.
CLEAN RESIDUAL OIL AFTER OPERATION
Lift the Retractable Guard to the maximum position
for 3 to 5 times. (See Fig.G2)
NOTE: The Oil Outlet cannot be faced towards
people. The Chain and Guide bar should be faced
down.
EN
Publicidad
