A nozzle type HF is suitable for use only on hard floor.
A nozzle of type CA is suitable for use only on carpet.
The other nozzles are accessories for specialist cleaning tasks and are recommended
for occasional use only.
The Crevice tool, Furniture nozzle and Dusting brush are stored on board under
the accessories door.
All accessories can be fitted to the end of the handle or the end of the telescopic
tube.
Accessory Set :
Crevice Tool – For corners and hard to reach areas. [w1]
Furniture Nozzle – For soft furniture and fabrics. [w2]
Dusting Brush – For bookshelves, frames, keyboards and other delicate areas. [W3]
Parquet Nozzle* – For parquet floors and other delicate floors. [Z]
Pet Hair Remover Mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for pet
hairs removal. [X]
Allergen Remover Mini Turbo Nozzle* – Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas, particularly suitable for allergen
removal. [Y]
IMPORTANT: Do not use mini turbo nozzles on rugs with long fringes, animal hides and
carpet pile deeper than 15mm. Do not keep the nozzle stationary while brush is rotating.
CLEANER MAINTENANCE
For models equipped with LED bag check indicator* (see H1), both full bag and
obstructions are signaled by a red light on the display.
For models equipped with the other type of bag check indicator* (see D), the mechanism
turns red if bag is full and if obstructions occur.
Replacing the Dust Bag
If the bag check indicator turns red on the bag door* (see D), or on the display*(see H1)
please check the bag and, if necessary, replace with it.
Lift the bag door release latch, open the bag door and remove the bag. [12,13] The
1.
full dust bag should be disposed correctly and carefully. [14]
2.
Fold a new bag as shown on the bag and fit by inserting the collar into the bag
holder. [13]
3.
Close the Bag door.
WARNING: The bag door will NOT close if the dust bag and/or the bag holder
are not assembled to the cleaner. Always ensure the bag is present when closing
the bag door.
REMEMBER: The bag check indicator also turns red (D or H1)** if an obstruction
has occurred. In this case refer to 'Remove a Blockage from the System'.
*Certain Models Only
** May vary according to model
Cleaning the Filters
To ensure constant optimum performances from your cleaner, please wash the
filters after each 5 bag changes.
Cleaning the pre-motor filter:
Lift the bag door release latch to open bag door and remove the bag. [12,13]
1.
2.
Remove the pre-motor filter frame from the cleaner. [15]
3.
Remove the filter from the pre-motor filter frame. [16]
4.
Wash the pre-motor filter and the pre-motor filter frame using hand warm water, and
allow it to dry thoroughly before inserting into the cleanerr. [19,20]
Cleaning the exhaust filter
1.
Remove the exhaust filter, unclip the exhaust filter cover and remove the exhaust
filter pack. [17,18]
2.
Wash the exhaust filter pack in hand warm water, and allow it to dry thoroughly
before inserting into the cleaner. [19,20]
Remember: Do not use hot water or detergents. In the unlikely event of the filters
becoming damaged, fit a Genuine Hoover replacement. Do not try and use the product
without a dust bag or filters fitted.
Cleaning the permanent cloth dust bag* (*Certain model only)
To maintain optimum performance we recommended that you wash the permanent cloth
dust bag after every 5 full bags. Empty the contents of the bag into a bin, wash the bag
under warm water, remove excess water and leave to dry fully before replacing.
Removing a blockage from the system
If the bag check indicator turns red* (D) or remains lit* (H1):
1. Check if the bag is full. If so refer to 'Replacing the Dust Bag'.
2. If it is not full, then:
A. Do the filters need cleaning? If so refer to 'Cleaning the Filter'.
B. Check if there is any other blockage in the system.
-
Use a cord or a stick to remove any blockage from the telescopic tube or flexible
hose.
Warning - The bag check indicator will remain red*or lit* if the cleaner is used when
the bag is full, if there is a blockage or if the filters are dirty. If the cleaner is used for
a significant period of time with the bag check indicator illuminated, an thermal cut
out will switch the cleaner off to prevent overheating. The bag check indicator turns
off once the cleaner has switched off to signal that the thermal cut out has been
activated. If this should happen, switch the cleaner off, unplug and correct the fault.
It will take about 30 minutes for the cut out to automatically.
3
GB