Publicidad
Idiomas disponibles
Idiomas disponibles
REMOVING CHUCK (FIG. Z)
1.
With the switch =OFF", open the jaws of the chuck as
wide as possible by turningthe chuck counterclockwise.
2.
Tap the chuck (1) lightly with a plastic tipped hammer
at the top of chuck, until the chuck releases.
NOTE: Place one hand below the chuck to catch it when
it 'fallsout.
Fig. Z
To avoid injury from an accidental start, ALWAYS make
sure the switch is in the "OFP position, the switch key is
removed, and the plug is not connected to the power
source outlet before removing or installing the chuck.
BASIC OPERATION
INSTRUCTIONS
To get the best results and minimize the likelihood of
personal injury, follow these instructionsfor operating your
drill press.
For your own safety, always observe the safety
INSTRUCTIONS
listed here and on pages 3, 4, and 5
of the instruction manual.
YOUR PROTECTION
b. Whenever possible, position the WORKPIECE to
contact the left side of the column.If it is too short
or the table is tilted, use the fence provided or
clamp solidly to the table, using the table slots.
c.
When using a drill press vise, always fasten it to
the table.
d.
Never do any work freehand (hand-holding the
workpiece rather than supporting it on the table),
except when polishing.
e.
Securely lock the head and table supportto the
column, and the table to the table support, before
operating the drill press.
f. " Never move the head or the table while the tool
is running.
g.
Before starting an operation,log the motor switch
to make sure the drill or other cutting tool does
not wobble or cause vibration,
h.
If a workpiece overhangs the table so it will fall
or tip if not held, clamp it to the table .or provide
auxiliary support.
i.
Use the fence provided or other fixtures for
unusual operations to adequately hold, guide,
and position workpiece.
j.
Use the SPINDLE SPEED recommended for the
specific operation and workplace material. Check
the panel on the inside pulley cover or the chart
below for drilling speed information.
For accessories, refer to the instructionsprovided
with each accessory.
5.
Never climb on the drill press tablet it could break or
pull the entire drill press down on you.
6.
Turn the motor switch "OFF", and put away the switch
key when leaving the drill press.
7.
To avoid injury from thrown work or tool contact, do
not perform layout, assembly, or set up work on the
table while the cutting tool is rotating.
_I:_
-'_ II_[e_
To avoid being pulled into the power tool, do not wear
loose clothing, gloves, neckties, or jewelry. Always tie
beck long hair.
1.
ff any part of your drill press is missing, malfunctioning,
damaged or broken, stop operation immediately until
that part is propedy repaired or replaced.
2.
Never place your fingers in a position where they
could contact the drill bit or other cutting tool. The
workpiece may unexpectedly shift, or your hand
could slip.
3.
To avoid injury from parts thrown by the spring, foUow
instructionsexactly when adjusting the springtension
of the quill.
4.
To prevent the workpiece from being torn from your
hands, thrown, spun by the to01, or shattered, always
properly support your workpiece as follows:
a.
Always position BACKUP MATERIAL (used
beneath workpiece) so that it contacts the left side
of the column, or use the fence provided and
clamp to brace a smaller workplece.
DRILLING SPEED TABLE (rpm)
Material
Wood
Alum.,Zlnc,Bnm
3600
3600
DrillBit
Diam.
(Inches)
1/16
1/8
3/16
1/4
5/16
3/8
1/2
2610
2610
1600
88O
Iron,Steel
36OO
2610
1600
88O
540
18
Publicidad
