Publicidad
Idiomas disponibles
Idiomas disponibles
<YHUSKY
4 Respect the tool as a working implement.
Never engage in horseplay.
@ Never pull the trigger unless nose is directed
toward the work.
@ Keep others a safe distance from the tool
while tool is in operation as accidental
actuation may occur, possibly causing injury.
AIR SUPPLY AND CONNECTIONS
@ The connector
on the tool must
not hold
pressure when air supply is disconnected. If
an incorrect fitting is used, the tool can remain
charged with air after disconnecting and thus will
be able to drive a fastener even after the air line
is disconnected, possibly causing injury.
@Do
not
use
any
type
of reactive
gases,
including, but not limited to, oxygen
and
combustible gases, as a power source. Use
filtered,
lubricated,
regulated
compressed
air
only.
Use
of a
reactive
gas
instead
of
compressed air may cause the tool to explode
which will cause death or serious personal injury.
O Use only a pressure-regulated compressed
air source to limit the air pressure supplied to
the tool. The regulated pressure
must not
exceed 100psi. If the regulator fails, the pressure
delivered to the tool must not exceed 200psi.
@ Always disconnect air source:
0 Before unloading or making adjustments.
@ When maintaining the tool.
@ When clearing a jam.
@ When touching the safety yoke.
@ When tool is not in use.
@ When moving to a different work area.
Such precautionary measures reduce the risk
of injury to persons.
LOADING TOOL
€ Do not load the tool with fasteners when any
one of the operating controls is activated.
@ Never place a hand or any part of body in
fastener discharge area of tool.
@ Never point tool at anyone.
@Do
not
pull the
trigger
or
depress
the
workpiece
contact
as accidental
actuation
may occur, possibly causing injury.
A WARNING:
The warnings and precautions discussed
above
cannot
cover
all
possible
conditions and situations that may occur.
It must be understood by the user that
common
sense and caution are factors
which cannot be built into this product,
but must be supplied by the user.
UNPACKING
@ This
tool
has
been
shipped
completely
assembled.
@ Make sure that all items listed in the packing
list are included.
@ Carefully
remove
the
tool
and
any
accessories from the box.
@ Inspect the tool carefully to make sure no
breakage
or
damage
occurred
during
shipping.
@ Do not discard the packing material until you
have
carefully
inspected
and
satisfactorily
operated the tool.
@ If any parts are damaged or missing, please
call 1-866-676-8468.
A WARNING:
If any parts are missing do not operate
this
tool
until
the
missing
parts
are
replaced. Failure to do so could result in
possible serious personal injury.
A WARNING:
Do not attempt to modify this tool or
create accessories
not recommended
for
use
with
this
tool.
Any
such
alteration
or
modification
is misuse
and could result in hazardous condition
leading
to possible
serious
personal
injury.
<YHUSKY
FEATURES
SPECIFICATIONS
REQUIRES: 5.47 SCFM with 100
fasteners per minute @ 80psi
AIR INLET: 1/4 inch NPT
MAGAZINE CAPACITY:
100 fasteners, 16 gauge
WEIGHT: 4.22 lbs
MAXIMUM PRESSURE: 110psi
PRESSURE RANGE: 70psi - 110psi
PIN SIZE RANGE: 1 inch to 2-1/2 inch
0.118"(3mm)
k—
E
25mm
E
32mm | | 1-1/4"
38mm | | 1-1/2"
45mm | | 1-3/4"
50mm
2"
64mm V 2-1/2"
Compatible with all brands of 16 gauge straight
finish nails .
FEATURES
0 360° ADJUSTABLE EXHAUST
Allows user to direct air away from face.
€ COMFORT-GRIP HANDLE
For increased comfort and control.
@ ERGONOMICALLY ENGINEERED BODY
Rugged and Comfortable resulting in a light-
weight tool great for extended use.
€ ADJUSTABLE DEPTH
Depth
is
easily
adjustable
for
various
applications.
@ QUICK-JAM RELEASE
Allows for easy access clearing in the event of a
jam.
€ NON-MARRING SAFETY CONTACT
Eliminates damage to working surface.
OPERATION
ADJUSTING THE EXHAUST
The adjustable exhaust on the cap of the tool allows
users to direct the exhaust according to operator
preference. To adjust the direction, turn the exhaust
cap in the desired direction.
LOADING FASTENERS
1. Connect the tool to the air source.
2.Insert
strip
of fasteners
from
the
rear
of
magazine(A). Be sure the fasteners are pointed
downward .(See figure 1 & figure 2)
3.This tool uses a spring loaded bypass lever in
order to load and upload the nails. Once the nails
are
properly
inserted,
pull
the
pusher(B)
completely back, pressing against the bypass
lever of the pusher.(See figure 3)
4.Once the pusher hits the back of magazine,
allow the pusher to slide forward and engage the
nails, pushing them to the nose of the tool.
(See figure 4)
©
A
Rear of magazine(A)
Y
Head of nail
INSERT NAIL STRIP
07
Publicidad
