enbrighten Landscapes RGBLL / 72 / 6 / 18 / 2 Guía Rápida

Seasons
Congratulations on your recent purchase of Enbrighten Seasons Landscape Lights.
Enbrighten Landscape Lights are designed to provide lighting for life with no bulbs to
replace ever again!
IMPORTANT: Before installation, please read all warning statements included at the bottom of
these instructions.
To ensure proper installation, please follow each step below:
Step 1 - INITIAL SETUP
1. Carefully unpack your lights from the box. Remove and dispose of the wire ties and plastic
bag (see warning on bottom).
2. Locate remote control and install 2 AAA batteries (included).
3. When installing landscape lights outside, a ground fault circuit interrupter (GFCI)
receptacle must be used. Before installing, plug the landscape lights into the GFCI
receptacle to ensure all lights work properly.
IMPORTANT: Unplug the landscape lights prior to installation.
Step 2 - INSTALLING LANDSCAPE LIGHTS
Each landscape light is designed with two universal keyholes for mounting the included
stakes (one per light) or for mounting on a flat surface (see below instructions).
Ground Mounting
1. Carefully plan your installation by laying out your
landscape lights in the desired sequence—starting with
the GFCI receptacle and power supply. The first light can
be within 10ft. of the power supply. Each subsequent
light can be placed within 8ft. of each other.
2. Mount the power supply using either the keyholes on
the back or ear-tabs on the side (see Figure A). Do not
lay the power supply directly on the ground or where
standing water may accumulate (see Figure B).
Figure B
Do not pull cord tight, leave
slack in loop to prevent
strain on power supply.
3. Ground mounting has two options for installation: placing the light directly
on the ground or using the included mounting stake.
a) Placing on the ground: lay each light directly on flattened ground such
as garden bedding, walkways, etc.
b) Using the mounting stake: insert the stake into either keyhole slot on
the bottom of the puck and firmly plant it into soil or mulch (see
Figure C). NOTE: If the stake requires more than a firm push, loosen
the soil or remove debris.
c) Cord-management: your Enbrighten landscape lights feature burial-
grade cable. This allows you to conceal excess cable by directly
burying it in the soil or covering it with garden bedding.
Flat-Surface Mounting
Lay out the landscape system in the manner in which you plan to install.
Only mount lights to a solid support structure, such as joist, beams,
studs or other solid mounting surfaces. Use two #6 pan head screws
(not included) of an appropriate length for the surface (See Figure D)
to properly mount the lights. Use the provided mounting template for
guidance.
Figure D
Important — please read:
Refer to the manual or visit www.byjasco.com for limitations and restrictions on warranties and the product registration information.
WARNING: When using outdoor-use portable luminaires, basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and
personal injury, including the following:
Ground Fault Circuit Interrupter (GFCI) protection is to be provided on the circuit(s) or outlet(s) to be used for the wet location portable luminaire. Receptacles are
available having built-in GFCI protection and are able to be used for this measure of safety.
WARNING: Keep these bags away from babies and children. Do not use in cribs, beds, carriages, or playpens. The thin film may cling to nose and mouth and
prevent breathing.
Warranty Information: This Jasco product is warrantied for three (3) years with a limited-lifetime replacement warranty on Enbrighten LED light source only.
MADE IN THAILAND
Distributed by Jasco Products Company LLC,
10 E. Memorial Rd., Oklahoma City, OK 73114.
This Jasco product comes with a 3-year limited warranty.
Visit www.byjasco.com for warranty details.
Questions? Contact our U.S.-based Consumer Care at 1-800-654-8483
between 7AM-8PM, M-F, Central Time.
Patents pending | www.enbrightenme.com
Landscapes
Figure A
Ear-tabs
6.38in./162mm
2in./50.8mm
Keyholes
Figure C
56067
Version 2
02/22
USING THE REMOTE
To power on or off your lights, press the red ON/OFF button located at the
top of the remote.
NOTE: Keep remote indoors when not being used. Remote is not waterproof.
Now that your lights are installed and powered on, take time to explore the
following settings that are programmable via your remote.
Single-Color Select
Find your favorite color on the remote's color pad, and simply push that
button to set all of the lights the same color.
NOTE: Within this feature, you can also press the dimming button to select
from 10 light levels. The dimming option is only available for single- and dual-
color selection.
Dual-Color Select
a) Press Color 1, then select a color from the color pad to set the color of
every other light starting with the first light.
b) Press Color 2, then select a color from the color pad to set the color of
every other light starting with the second light.
c) During the selection feature, press the dimming button to choose one of 10 light levels.
White Select
By pressing the white button, you can cycle through white selections — 2200K, 2700K and 5000K.
Strobe
By pressing the "Strobe" button, the lights cycle through all of the colors in a random pattern.
Fade
By pressing the "Fade" button, the lights slowly transition through all of the colors in a random pattern.
Modes
Press the "Modes" button repeatedly to cycle through the following preset modes:
•Twinkle •Multi-Fade •Christmas •St. Patrick's Day
•Red, White and Blue •Fall •Spring •Multi-Colors
NOTE: Your landscape lights automatically remember the last customized settings and turn on in the
same mode and/or color scheme.
Timer
By pressing the "2 hour timer" button, you activate a two-hour countdown until lights turn off.
By pressing the "4 hour timer" button, you activate a four-hour countdown until lights turn off.
Pair your remote with additional lights
Your remote can be paired to additional sets of Enbrighten Seasons Landscapes Lights and
Enbrighten Seasons Café Lights. Follow the instructions below.
1. Plug in (or supply power) to the lights, and within 8 seconds, press and hold the ON/OFF button.
The lights will turn white, blink once and remain white. Your remote and lights are now paired.
a) Please note you can pair a remote with as many Enbrighten Seasons Lights as you desire.
b) Multiple strings can be paired simultaneously with one remote by suppling power to multiple
strings at once, then pressing and holding the ON/OFF button within 8 seconds of power on,
per the above instructions.
2. Lights can be paired with up to eight remotes. If you wish you remove a remote control
from memory of a light (unpair), follow the below instructions:
a) Plug in (or supply power) to the lights, and within 8 seconds, press and hold
the yellow button (in bottom left corner). The lights will turn white, blink twice and remain
white. Your remote and lights are now unpaired.
b) Multiple lights can be unpaired simultaneously from one remote by suppling power to
multiple lights at once, then pressing and holding the yellow button within 8 seconds of
powering on.
Electrical ratings
Input: 120V, 50/60Hz
Input Watt, Max.
RGBLL / 72 / 6 / 18 / 2 26W
RGBLL / 102 / 9 / 18 / 2 36W
RGBLL / 132 / 12 / 18 / 2 50W
WARNING
RISK OF ELECTRIC SHOCK
• RECEPTACLE OUTLETS USED FOR POWERING
LANDSCAPE LIGHTS SHALL COMPLY WITH ALL
NATIONAL AND LOCAL ELECTRICAL CODES.
CONSULT LOCAL ELECTRICIAN IF UNSURE OF
COMPLIANCE REQUIREMENTS.
• FOR USE ONLY ON GFCI PROTECTED CIRCUITS.
• DO NOT SUBMERSE.
• DO NOT USE AROUND AQUARIUMS.
• LANDSCAPE LIGHTS ARE A WET-LOCATION
PRODUCT AND HAVE NO SERVICEABLE PARTS.
• DO NOT USE WITH EXTENSION CORD, NEAR WATER
OR WHERE WATER MAY ACCUMULATE.
• KEEP LAMPS AT LEAST 16 FEET FROM POOLS
AND SPAS.
• KEEP PLUGS AND RECEPTACLES DRY.
• AVOID DAMAGE TO THE CORDS AND LAMP
ASSEMBLIES DURING INSTALLATION. PERIODICALLY
INSPECT THE LANDSCAPE LIGHTS FOR PHYSICAL
DAMAGE OR OTHER DAMAGE CAUSED BY OUTDOOR
EXPOSURE TO THE ELEMENTS.
READ IT OR WATCH IT
Read instructions or watch easy-to-follow video.
Scan QR code or visit https://byjasco.com/56067i
WET
• REPLACE ANY DAMAGED LANDSCAPE
LIGHTS.
• DO NOT INSTALL IN LOCATIONS WHERE
LANDSCAPE LIGHTS CAN BE STEPPED ON.
• ENSURE LANDSCAPE LIGHTS ARE
UNPLUGGED FROM POWER DURING
INSTALLATION.
• CHILDREN SHOULD NOT PLAY WITH
LANDSCAPE LIGHTS.
• UL RECOMMENDS TESTING GFCI CIRCUITS
AND RECEPTACLES EVERY MONTH TO
ENSURE PROPER OPERATION.
RISK OF FIRE
• LANDSCAPE LIGHTS ARE DESIGNED TO
BE MOUNTED WITH THEIR INDIVIDUAL
KEYHOLE MOUNTING FEATURE. DO
NOT MOUNT LANDSCAPE LIGHTS USING
THE MAIN ELECTRICAL CORD OR THE
INDIVIDUAL DROP CORDS.
• NOT INTENDED FOR INSTALLATION IN
CEILINGS, SOFFITS, CABINETS, ATTICS, OR
OTHER ENCLOSED SPACES.