Bosch NGM30 Manual De Instalación página 7

Note: T heappliance s houldnotbeinstalled witha
ventilation s ystem thatblows airdownward t oward the
burners. Thistypeofventilation s ystem maycauseignition
andcombustion p roblems w iththegascooking appliance
resulting inpersonal injuryor unintended operation.
Installation Procedure
WARNING
To avoid electrical shock hazard, before installing
the cooktop, switch power off at the service panel to
prevent the power from being switched on
accidentally.
cutout as shown by the dotted line in Figure 4: "Counter
Cutout- Foam Tape Placement". Leave 114"(6.35mm) gap
between the foam tape and the edge of the cutout.
,-................................................................. _ " 1/4"
___, Foam
Tape
iiii ii i i i iii ii i iii ii i i i iii ii i iii ii i i i iii ii i iii ii i i i iii ii i i i iii ii i iii ii i i i iii ii i iii ii i i i iii ii i iii ii i i i iii ii i i i iii ii i iii ii i i i iii ii i iii ii i i i iii ii i iii ii i i i iii ii i i i iii ii i iii ii i i i iii ii i iii ii i i i iii ii i iii ii i i i iii ii i i i iii ii i iii ii i i i iii ii i iii ii i i i iii ii i iii ii i i i iii ii i i i iii ii i iii ii i i i iii ii i iii ii i i i iii ii i iii ii i i i iii ii i i i iii ii i iii ii i i i iii ii i iii ii i i i iii ii i iii ii i i i iii ii i i i iii ii i iii ii i i i iii ii i iii ii i i i iii ii i iiiil
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
Figure 4: Counter Cutout - Foam Tape Placement
Prepare the Countertop
Cut out the countertop per the dimensions shown in
"Cabinet Requirements" on page 3.
Some solid surface materials, such as Surell
TM
and
Corian®, require different cutting methods. Consult with the
solid surface manufacturer for the correct cutting method
needed. Apply heat reflective tape such as Scotch
Aluminum Foil Tape #425 or #427 (not included) around the
cutout so that it folds over on the top and sides. Do not
wrap the tape underneath the cooktop. Be sure the tape
extends beyond the outermost flange of the cooktop. All
corners should be covered with tape.
Iil_ " Cutout shows location A_A
i: 4F_ of Aluminum Reflective Tape
Heat Reflective Tape
Section "A - A"
Figure 3: Counter Cutout - Solid Surface Countertops
Seal the Cooktop with Foam Tape
Apply the self adhesive foam tape in one continuous
rectangle directly to the counter around the perimeter of the
Install the Cooktop
Insert cooktop into the cutout. Attach clamps of the hold-
down brackets packaged with the cooktop to the rough-in
box. Use the washer and screws provided.
Roughqn Box
fJ
Clamp
_ Adjusting
Screw
Tape _q Wooden Block
(Seal) _._ 0o be used with
- solid surfacing
material, i.e.
_Surell
TM
and
Figure 5: Attaching Hold-Down Brackets
Adjust hold-down brackets to desired position and tighten
screws to rough-in box. Insert adjusting screw into clamp
and secure cooktop to countertop.
NOTE:
For solid surface material installations: Insert a wooden
block between the end of the screw and the bottom of the
countertop. Do not overtighten adjusting screw. Trim
excess aluminum tape around cooktop flange.
English 5