Publicidad
Idiomas disponibles
Idiomas disponibles
The refrigerator andfreezer controls arelocated o nthe
dispenser panel.
IMPORTANT=
The display s creen o nthedispenser control panel
willturnoffautomatically andenter " sleep" m ode when the
control buttons anddispenser padhave notbeen used for
2 minutes or more. Whilein"sleep" m ode, thefirstpress o fa
control button willonlyreactivate thedisplay s creen, without
changing anysettings.
• Touch a nycontrol button onthedispenser panel toactivate
thedisplay screen. The home screen willappear a sshown.
Adjusting the Controls
For your convenience, your refrigerator
and freezer controls are
preset at the factory. When you first install your refrigerator,
make sure that the controls are still set to the "mid-settings."
The
factory
recommended
set points are 37°F (3°C) for the
refrigerator
and O°F (-18°C) for the freezer.
IMPORTANT:
Wait 24 hours before you put food into the refrigerator.
If
you add food before the refrigerator
has cooled completely,
your food may spoil.
NOTE= Adjusting the set points to a colder than
recommended
setting will not cool the compartments
any
faster.
•
If the temperature is too warm or too cold in the refrigerator
or freezer, first check the air vents to be sure they are not
blocked
before adjusting the controls.
•
The preset settings should be correct for normal household
usage. The controls are set correctly when milk or juice is as
cold as you like and when ice cream is firm.
•
Wait at least 24 hours between adjustments.
Recheck the
temperatures
before other adjustments are made.
To view and adjust the set points, press and hold the
TEMPERATURE button for 3 seconds. When adjust mode is
activated,
adjusting information
will appear on the display
screen.
NOTE= To view Celsius temperatures,
press the LIGHT button
when adjust mode is activated.
To return the display setting to
Fahrenheit, press LIGHT again.
•
When adjust mode is activated,
the display screen shows
the refrigerator
set point and "REFRIGERATOR" appears.
•
Press LOCI( to raise the set point, or press ACCELER-ICE to
lower the set point.
•
When you have finished viewing (and adjusting if desired)
the refrigerator
set point, press TEMPERATURE to change the
display to show the freezer set point. When the zone has
been changed, "FREEZER" appears on the display screen.
•
Press LOCI( to raise the set point, or press ACCELER-ICE to
lower the set point.
•
When you have finished viewing (and adjusting if desired)
both the refrigerator
and freezer set points, press RESET
FILTER to save the settings.
NOTE= To exit without saving changes, press WATER/ICE
at
any time while in adjust mode, or allow about 60 seconds of
inactivity
and adjust mode will turn off automatically.
When adjusting temperature
set points, use the following
chart
as a guide.
CONDITION:
TEMPERATURE
ADJUSTMENT:
REFRIGERATOR too cold
REFRIGERATOR Setting
1° higher
REFRIGERATOR too warm
REFRIGERATOR Setting
1° lower
FREEZERtoo cold
FREEZERSetting 1° higher
FREEZERtoo warm /
FREEZERSetting 1° lower
Too little ice
The set point range for the refrigerator
is 33°F to 45°F (O°C to
7°C). The set point range for the freezer is -5°F to 5°F (-21°C to
-15°C).
Cooling On/Off
Your refrigerator
and freezer will not cool when cooling is
turned off.
•
To turn cooling off, press and hold the LOCI( and RESET
FILTER buttons at the same time for 3 seconds.
IMPORTANT= To avoid unintentionally locking the dispenser
or changing
other settings, be sure to press both buttons at
exactly the same time.
Publicidad
