Publicidad
Idiomas disponibles
Idiomas disponibles
PREPARATION
FOR USE
The stand of this TV is li_)ldedwhen you pur-
chased. Place this TV face-down oi1a flat sur-
face covered with the suit cloth. Bend the
stand slowly to tbrward until it clicks.
Do not bond from this side. _
If you want to told the stand again, insert a
thin rod iuto tire hole in the right side of the
stand as illustrated,
bend the stand backward
while you keep pushing the hole.
[_I0]#I#I=[_1i [0] #[,."1
Plug the incoming
cable into tile ANT.jack
on the rear of the TV.
"
:
Real- ol Ihis TV
7 j4
lnc'Oll/illg
cable
llOll/
]1o11/_.:
Aiitcnlla
/
__ [ Cable Company (No Cable Box/
Cable
BOX
O1"
Sal_.:lhte
Bt x"
OR
_
....
NOTE (DO NOT DISCONNECT FROM BOX)
lnconfing cable fl-om Cable
Some cable TV systems use scrambled signals and require
Company or Satellite Antenna
a special converter to receive these channels. Consuh
your local cable company.
[You can bracket this product as wall lnounting TV using the arm adapted tor 1001nm (COlnmerciall3 available). [
CAUTION:
TO PREVENT
ELECTRIC
SHOCK,
MATCH WIDE BLADE
OF PLUG TO
WIDE SLOT, FULLY INSERT.
ATTENTION:
POUR EVITER
LES CHOC ]ELECTR1QUES,
INTRODUIRE
LA LAME LA
PLUS LARGE
DE LA FICHE DANS LA BORNE CORRESPONDANTE
DE LA PRISE ET
POUSSER
JUSQU'AU
FOND.
Note:
* For your safety and to avoid damages
to the unit, unplug
the antenna
cable from the
ANT jack before moving
the unit.
I/111/[.'1 f:1 _lm]
[EXTERNAL
CONNECTION]
VIDEO1
input
_]:i>
J
Audio
( al)le
Video Cable
S-Video Cable
:
@
¢}
Rear ol this TV
Notes:
l* Tire AUDIO
L jack is for lnouo input. Tire sound is heard from both speakers.
Use this jack for
connecting
nlonaural
audio equiplneut.
* The S-VIDEO
jack
s g ven pr or ty over tre VIDEO jack.
VIDE02 input
Rear
ot/]lis
TV
Video
Calllera
OUT,
Audio Cable
J
(OUT)
Coll/l)
Ollent
Video Cable
tD
Video Grille
Notes:
* This TV can accept 48(1p / 480i / simplified
1080i video signal.
* Simplified
1080 video signal differs to the original
1080i video signal because
it is displayed
alter converted
into 48( p signa.
rr[@
[_1@
[_@
Installtw'oAhAbatteries(sul)plied)matehiug
tire polarity indicated iuside battery colnpart-
meut of the remote control.
[BATTERY
PRECAUTIONS]
• Be sure to follow the correct polarity as iudicated
in the battery colnpartment.
Reversed
batteries may cause damage to the device.
• Do not mix dittewnt types of batteries together (e.g. Alkaliue and Carboo-Zinc) or old balteries with tl_sh ones.
• If the device is not to be used lbl a long period of time, remove the batteries to preveut
damage or injury from possible battery
leakage.
• Do riot try to recharge batteries
riot intended
to be recharged;
they can overheat
and lupture.
When you turn on the power for the first time, the "SELECT
LANGUAGE"
menu is displayed.
The "INITIAL SETUP" menu is displayed every time ' ou turn on the unit unless the scanning is completed.
_
Select tire desired
1"_
. ...........
language according to
....................
tire screen indication.
E ..........................
After that, tire TV
F_N_
.....................
performs
"AUTO
PRESET
CH" to scan
-
chmmels
available
to,"
_
........
::l,)_;:N::tR'
L
.......
tire broadcasting
ill
i_:_?:;_:::::NIT
your area.
_o_"E_ET_"
If the TV screen shows
I
...........
snow l,oise and there is [__%:_i_:_i'_i!)
_
than 5 seconds,
[
.......................
"HELPFUL
HINTS"
appears.
Follow the
instructions
listed on-
screen.
When tire scanuiug is colnpleted,
or [MENU]
is )ressed during channel scanuiug to cancel it, tire
ttuler
stops
OU
the lowest
lllelllOrized
chanl_le[.
Notes:
In case no channel can be received by the channel scanning,
"NO TV SIGNALS"
is displayed on
the screen. Turn off the unit and clreck the antenlm connection,
then tollow' step 1 again.
If those settings do not work properly, please call our hell? line on the front page of this owner's manuah
When you nse the AUDIO/VIDEO
input jacks, select _WIDEOI"
or "VIDEO2"
mode by
pressing [INPUT
SELECT]
on the remote control or [SELECT]
on the main unit. The input
mode
changes
by pressing
the button
as following:
INPUT
TV channel
_
VIDEO'[
_
VIDEO2
8ELECT
Tilt Stand
1o
Adjust tire stand to change tire angle of TV (-5 ° _ l().
OPERATIONS
IR transmitter
To scud infrared
ray (IR) signal
POWER button
To turn TV on/off
VOL A/V buttons
To adjust volume
To decide the commaM of settings
MENU
button
To view on-screen
menu
MUTE button
To rnute souud
DISPLAY button
To display CH No./Audio Status
button
To select TV or external input
&/_
buttons
To select channels aud move
up/down through nlenu itenls
number buttons
Press two digits to directly access the
desired channel. Remember to press
a "11" b etore a single digit channel.
Press to select cable channels
higher than 99.
button
To set Sleep Tilner
RET button
To return to previous channel
Note:
* You ct).ll test it' tile renlote control sends out tire iufrared
signal with an AM radio.
(Refel to "TROUBLESHOOTING
GUIDE".)
MENU
V VOLUME
©
MENU
button
To view on-screen
menu
VOLUME
A/_
buttons
To adjust volume
CHANNEL
_/Y
buttons
To select chanuels
F
ELECT
button
To select TV or external
input
POWER
button
_To
turu TV on/off
• CHANNEL.
SE_CT
_R
I
Infrared
Sensor
Window
.Note:
If some digits appear in tire corner of tire screen when tire unit is turned on at tire first time,
press
[POWERI
without unplugging
the powel cord.
Publicidad
