Publicidad
Idiomas disponibles
Idiomas disponibles
into its place on your furniture. (Figure A4)
•
Attach the long and corner plastics of
ventilation that will direct the air to the
bottom of the furniture, and attach them
to the corner plastic you have attached to
the back of the stove as shown in figure
B5. In order to attach it to the corner
plastic, you need to lift the hob a little
from the back. Ventilation plastic parts
must have been mounted as shown in
figure B6.
•
Attach the ventilation outlet bit to the
ventilation corner plastic from the bottom
of your furniture as shown in figure B7.
•
Put your drawers back in place. (Figure B8)
•
Remove the metal oil filter by pulling it
upwards. (Figure B9)
•
Remove the liquid collection chamber as
shown in figure B9.
•
Place two units of active carbon filters to
right and left as shown in figure B10.
•
Place back the liquid collection chamber
as shown in figure B11. Complete the
installation by placing back the metal oil
filter.
Air Routing Parts
•
Air routing parts which will be used
in type B installation should only be
purchased from "Naber" company.
•
The parts required for using type B
installation with a 10 cm air routing parts
are given in table B12. You may see the
part code of the company for same part
is in the Y column. Parts marked with *
were optional for users who wanted to
use air vent.
•
The parts required for using type B
installation with a 6 cm air routing parts
are given in table B13. You may see the
part code of the company for same part
is in the Y column. Parts marked with *
were optional for users who wanted to
extend the air outlet.
C type installation (Installation
with external circulation)
Preparation of the furniture on which
installation will be made: (Figure C2)
Prepare your furniture according to the
dimensions presented in Figure C2. Cut
dimensions for flush-fit installation are also
indicated in Figure C2. You need to obtain
the plastic parts of the air guide described in
this installation from the authorized service
or authorized dealers. These parts are not
supplied with the product.
20
Steps for C type installation
•
Place the ventilation corner plastic
described in Figure C3 in its slot on the
back of the hob as shown in the figure.
•
Completely remove the drawers of your
furniture and place your stove by tilting it
into its place on your furniture. (Figure C4)
•
Attach the long and corner plastics of
ventilation that will direct the air to the
bottom of the furniture, and attach them
to the corner plastic you have attached to
the back of the stove as shown in figure
C5. In order to attach it to the corner
plastic, you need to lift the hob a little
from the back. Ventilation plastic parts
must have been mounted as shown in
figure C5.
•
Reach at your chimney using ventilation
parts in accordance with its location.
•
The air outlet direction shown in the
installation drawings is given as an
example. You may install in other
directions.
Air Routing Parts
•
Air routing parts which will be used
in type C installation should only be
purchased from "Naber" company.
•
For type C installation, it should be
determined which parts should be used
before installed. The quantities of parts
that can be used in the installation may
vary according to the installation location.
•
All parts that can be used in the
installation are given in table C9. You may
see the part code of the company for
same part is in the Y column.
Electrical connection of the appliance
(Figure E)
•
Connect the appliance to a grounded
outlet/line protected by a fuse that
is compatible with the values in the
"Technical specifications" table. Have the
grounding installation made by a qualified
electrician while using the product with or
without a transformer. Our company shall
not be liable for any problems arising
due to the product not being earthed in
accordance with the local regulations.
•
Disconnect the appliance from the
electric connection before starting any
work on the electrical installation. Risk of
electric shock.
•
The appliance may only be connected
to the mains electricity connection by
an authorized and qualified person.
The manufacturer shall not be held
responsible for any damages that may
occur as a result of operations performed
Publicidad
