Publicidad
Idiomas disponibles
Idiomas disponibles
Notes
During Assembly
Use
a
soft platform below the parts to avoid scratches and damages.
THIS SIDE
ODE
Please
note you install the panels
with the
UV
protected
side
out
(marked
with
"THIS
SIDE
OUT")
remove plastic
film
before inserting panels and locking
in
place.
Product dimensions
can be
adjusted to your specific
needs:
1.
The
wall-mounting
profile (top-back)
can be
adjusted from 260
to
305 cm
(102.4"
to
120")
above ground.
The
adjusting
is
done when measuring and drilling (Step
5).
Please
note the installation recommendations' height suggested
in
Diagram
A.
It
is
possible to fix the
Patio Cover back
wall
height
at the lowest
point of 260 cm/102.4".
This
method
is
optional if the
assembly
conditions
and
exterior walls do not allow to
follow
the suggested installation
as
appears
in
the manual.
Please
note
that
the product appearance
may
slightly
change
as
a
result,
however snow load
weight
does
not
change.
2. Poles
distance from the wall
can be
adjusted from 226
to
286 cm (89"
to
112.6")
as
suggested
in
Diagram
Bl.
Poles
distance from the
side edges can be
adjusted from
5
to
54 cm
(2"
to
21.6")
as
suggested
in
Diagram
B2.
The
adjusting
is
done after assembly and before anchoring (Step 22)
by
sliding
poles and
profile 7030+7031
at the
roof
profiles' channels.
3. Wall
mounting
and distance
from the wall determine the roof angle and the total depth of the product (distance of
gutter from the
wall). Higher wall
mounting
and shorter distance between wall and poles increase the
roof angle and
shorten the total depth
as
suggested
in
Diagram
C.
M
Steps
Step
5: It
is
important
to plan the installation
area,
mark
as
per the instructions and level the surface
prior to the
assembly. Make sure you
use
suitable
screws and anchors.
Step
11:
Apply
silicone sealants above beam 7288
+
7289,
in
order to prevent water from seeping
in.
Step
13:
Make sure
that
the angle between the back wall profile and the
panel
supporting
profiles
is
90
degrees.
Step
15:
Please
note you install the panels
with the
UV
protected
side
out
(marked
with
"THIS
SIDE
OUT")
remove plastic sticker
as
panels
are
locked
in
place.
Step 19b: Apply silicone
sealants on
both
sides
of
the part combining 8080 & 8079
in
order to prevent water
leakage,
as
shown
at
the drawing 19b.
Step 20a: Apply silicone
sealants on the inner part
of 7997, and connect to the profile
as
depicted
in
drawing 20a.
Step 20c:
Do
not tighten
screw
4043
yet,
in
order to allow the final adjustments done
in
step
22b.
Step 22a+22c:
Please
adjust the
poles (inside
out
and sideways) by sliding
them to their final position prior to
anchoring.
Make sure
that
the
poles distance
from the
Patio
cover side edge does
not
exceed 54 cm/21.3".
Step
22b: Adjust the gutter
head's
angle according to your needs and
tighten
screws
4043.
Step 24: Anchoring this product to the ground
is
essential
to
its
stability
and rigidity.
It
is
required to complete
this
stage
in
order for your warranty to
be
valid.
*Tighten
all screws
when completing assembly.
Note:
The
wall anchoring kit supplied
with this product
is
suitable only for concrete
walls.
Other wall types
need
an
accordant wall fixation
kit.
II
260-305cm
102.4"-120"
226-286cm
89"-
112.5"
13°
LTJ
17°
Publicidad
