Braun BC13-DCF Instrucciones Para El Usuario página 3

RC signal strength indicator (Image 5)
The signal indicator displays signal strength in 3 levels. Wave seg-
ment flashing means the time signals are being received. Press
and hold the RCC key for over 3 seconds until "OFF" is displayed to
disable the automatic RC function.
Note: You may use the RCC key to receive the time signal manual-
ly. The receive mode stops automatically after 6 minutes.
Setting the time
1. Slide the TIME SETTING / NEUTRAL / ALARM SETTING switch to
the TIME SETTING position.
2. Press the '+' or '-' key to set the desired value. Press and hold the
'+' or '-' key to speed up the setting.
3. Slide the TIME SETTING / NEUTRAL / ALARM SETTING switch to
the NEUTRAL position to return the normal display and save the
settings.
Setting the alarm
1. Slide the TIME SETTING / NEUTRAL / ALARM SETTING switch to
the ALARM SETTING position.
2. Press the '+' or '-' key to set the desired value. Press and hold the
'+' or '-' key to speed up the setting.
3. Slide the TIME SETTING / NEUTRAL / ALARM SETTING switch to
the NEUTRAL position to return the normal display and save the
settings.
Using the alarm and snooze function
1. Enable the alarm by shifting the ALARM ON / OFF slider up (so
the green detail is visible). The bell icon will appear on the LCD
display, and the alarm time will show on the LCD display for 3
seconds.
2. Tap the SNOOZE / LIGHT touch button to stop the alarm and ac-
tivate the snooze function. When the snooze function is activated,
the bell icon will flash.
3. To disable the alarm and snooze function, shift the ALARM ON /
OFF slider down. The bell icon will disappear.
Note: When the snooze function is activated, the alarm will auto-
matically start again after 5 minutes. The snooze function will not
stop unless the ALARM ON / OFF SLIDER is shifted down.
Placing the sensor outside
1. Place the sensor outside within a 30 metre (98ft) range of the
main unit.
2. The sensor can be placed vertically on flat surface under a
covered area which can shield it from direct sunlight or wet
conditions for an accurate reading. Or it can be mounted on a wall
with a screw.
3. Extreme temperatures, placing on wet surface and shock
should be avoided to prevent damage.
Note:
1. If no signal is received or the transmission is interrupted, the "-
-" symbol will appear on the LCD display.
2. Ensure that the main unit and the sensor are placed within a
30 metre (98ft) range from each other. Press the PAIR button to
receive the sensor signal.
3. If the "- -" symbol is still showing on the LCD display, please
reset the main unit and then the sensor.
4. The temperature and humidity ranges are as follows. It will
display HH when the environment is higher than this range. It will
display LL when the environment is lower than this range.
Temperature Humidity
Main unit -10 ~ 50 ºC 20 ~ 95%
Sensor -20 ~ 60 ºC 20 ~ 95%
Weather forecast indicator
The built-in barometer can detect atmospheric pressure chang-
es. Based on the data collected, it can predict the weather condi-
tion (image 6) in the forthcoming 12 to 24 hours.
Note:
The weather forecast predicts the weather condition in the forth-
coming 12 to 24 hours. It may not necessarily reflect the current
situation. We do not accept any liability which may occur as a
result of an incorrect weather forecast.
Setting the night light
1. Slide the BACKLIGHT switch to ON position to enable the night
light mode.
2. Slide the BACKLIGHT switch to OFF position to disable the
night light mode.
Note: The backlight will only turn on in low-light conditions, such
as in a dark room. If this feature is used continuously, the battery
life will be greatly reduced.
The continuous night light mode function will temporarily be
disabled for period of approx. 6 minutes at the hours of 2am 3am
or 4am, as during this time the clock is updating Radio Controlled
signal. Once the reception has been successfully updated the
continuous night light mode will automatically be restored.
During this time, if required, press Snooze/Light button to
activate the backlight function for 10 seconds.
Battery replacement
When the 'Low battery indicator' is visible on main unit, replace
with two new AA batteries at once.
When the 'Low battery indicator' is visible on sensor, replace with
two new AAA batteries at once. Press the PAIR button on main
unit to receive the sensor signal.
Note: Exposure to an electrostatic environment may cause the
clock to reset. In this event please follow the instructions as
described in this manual to set the clock again.
Guarantee
2 year guarantee against material and workmanship defects
(except battery). The guarantee is valid in those countries where
the alarm clock is officially being sold.
Broken or cracked lens screens are not covered under the
Guarantee.
Braun helpline
Should you have a problem with your product, please check your
local service centre at:
www.braun-clocks.com
www.braun-watches.com
or contact +44 808 175 3235 (calls free within the UK)
or +44 208 208 1833.
WARNING! This product is covered by the Waste Electrical
and Electronic Equipment (WEEE) directive. It should not be
discarded with normal household waste but taken to your local
collection centre for recycling.
EU Declaration of Conformity
We ZEON LIMITED UK, manufacturer of Braun Watches & Clocks
under licence from the Procter & Gamble Company hereby
declare that model BC13-DCF conforms to Directive 2014/53/EU.
The full text of the EU Declaration of Conformity can be viewed
on our website at
www.braun-clocks.com
Frequency band : 77.5KHz
Transmit power : 0 dBm
Certain trademarks used under license from the Procter & Gam-
ble Company or its affiliates.