YATO YT-99500 Manual De Instrucciones página 12

EN
The heater is not suitable for installation in the ceiling or fi xing to walls or directly to the ceiling and must be suspended on a chain.
If necessary, the chain can be shortened by cutting off the excess length.
For the YT-99500 heater, attach the chain holder (II) to the heater housing and then attach the chain to the holder with a latch
connector.
For the YT-99501 heater, attach the chain directly to the holder in the heater housing (III).
Check that the device switch is in the OFF or O position and plug the power cord plug into the power supply socket. The heater
is ready for use.
YT-99520 heater installation
Warning! Before starting any assembly work, make sure that the device is disconnected from the power supply socket and is
completely cooled down.
This is a portable type heater and cannot be fi xed to walls or ceilings. Mount the base (IV) to the device using screws.
Place the heater on the fl oor. A minimum of 1.5 m distance from persons, walls or objects should be kept around the front wall of
the heater. The rear wall of the heater should be at least 0.5 m away from people, walls or objects.
Check that the device switch is in the OFF or O position and plug the power cord plug into the power supply socket. The heater
is ready for use.
Warning! Do not transport the device when it is hot. This can cause serious burns. To move the device, grasp it by the handle.
YT-99530, YT-99531, YT-99532, YT-99536 heater installation
Warning! Before starting any assembly work, make sure that the device is disconnected from the power supply socket and is
completely cooled down.
The heater can be installed directly on the wall or on the YT-99570 or YT-99571 rack. This type of heaters cannot be installed on
the ceiling or on the ceiling beam.
The heater must be installed at a height of at least 1.8 m from the fl oor and at least 0.5 m from the ceiling. Tilt the heater so that
its front wall faces the fl oor at an angle of approx. 45 degrees.
The heater is equipped with a three-element or four-element mounting system.
Connect the element of the assembly system using screws and nuts and then fi x them to the rear wall of the heater (V).
Make sure that the elements supporting the heater during transport (VI), if present in the device, are removed before connecting
the heater to the power supply. Leaving these elements will cause them to melt down, which can result in damaging the device,
as well as cause fi re. It is recommended to keep the elements in case of future transport of the device.
Check that the device switch is in the OFF or O position and plug the power cord plug into the power supply socket. The heater
is ready for use.
Using the heater
Turn the heater on by moving the switch to the ON or I position. For the YT-99530 heater, the switch must be moved to one of the
heating power positions. The more dots the higher the heat output.
The heater starts up and begins heating the room. If the room is larger than the maximum heating area, several heaters should be
placed in the entire room area, with even spaces between them. Otherwise, the device will not function eff ectively.
The speed of heating a room depends on several factors, its dimensions, the indoor temperature, the heat loss rate in the room,
e.g. due to insuffi cient thermal insulation.
After heating, turn off the heater by moving the switch to the OFF or O position and then unplug the power cord from the socket.
If the device is equipped with a remote control, it can be used to turn the device on and off and to set the heating degree, if the
remote control is equipped with such a function. Remote control operation is only possible when the device switch is in the ON
position. Turning the device off using the remote control does not fl ip the switch to the OFF position. Turning off using only the
remote control cannot be regarded as turning the device off .
Maintenance
Warning! Before starting any maintenance work, make sure that the device is disconnected from the power supply socket and
is completely cooled down.
Clean the device housing with a cloth slightly dampened with water and dry it. Clean the area around the heating lamp and the
vent holes with a stream of compressed air of not more than 0.3 MPa.
Never immerse the device in water or any other liquid and do not clean it with a jet of water or any other liquid.
Store the device disconnected from power supply. The power cord must be unplugged from the power supply socket. The place
O R I G I N A L I N S T R U C T I O N S
12