Publicidad
Idiomas disponibles
Idiomas disponibles
Operating Instructions
Display
Charging Status
READY
CHARGING
CHARGING COMPLETE
Automatic Charging
•
With the product powered, it starts charging few seconds after
connecting the charging handle to the vehicle's charging port.
•
The product automatically detects outlet voltage and maximum
allowable input current of your vehicle.
1. Press the release lever, plug the SAE-J1772 connector
of the charging handle to the vehicle's charging port.
The charging process starts.
2. The product switches off automatically once the vehicle's
battery is fully charged.
NOTICE: When the charging is complete, press the release lever
and unplug the SAE-J1772 connector, covering the handle with
item E after use.
User Maintenance Instructions
WARNING: The product contains no user serviceable parts.
Do not attempt to repair or service any other part of the product
yourself.
WARNING: The maintenance, and servicing of the product
must only be performed by qualified personnel in accordance with
applicable local regulations
WARNING: Disconnect the charging handle from the vehicle's
charging port and switch the circuit breaker off before cleaning.
•
Do not use cleaning solvents to clean any part of the product.
•
Cover the charging handle with the protective cover before
cleaning.
•
Regularly clean the product using a soft, dry cloth to remove
accumulated dust and dirt.
•
Regularly inspect the charging cable and plug for any visible
damage or wear.
Moving and Storage Instructions
WARNING: When transporting the product, handle with care.
Do not subject it to strong force or impact or pull, twist, tangle,
drag or step on the product, to prevent damage to it or any
components.
•
Cover the charging handle with the protective cover before storing.
•
Protect the product from any external impact.
•
Store the product in a dry indoor area and within the storage
away from children and pets.
Free Warning Label Replacement
If warning labels become illegible or are missing, please call
1-855-815-1171 for a free replacement.
Description
Standby status
Charging is in progress
The charging process
is complete
. Keep
Troubleshooting
Problem
Possible solution
The vehicle is not
• Verify that the product has power:
responding or
charging.
• Verify that the connector of the
• Verify that the vehicle has been
• Inspect the product for damage.
Error Codes
Error
Problem
code
E1
Voltage Error
E2
Plug Failure
E3
Over Current
E4
Ground Fault
Current Leakage
E5
Over Temperature
E6
E7
Relay Failure
E8
Failed Self-check
E9
Diode Fault
E10
CP Fault
NOTICE: If solutions can not solve the problem, stop using the
product. Switch the circuit breaker off and contact customer
service for support.
Accessories
WARNING: Since accessories, other than those offered by
D
WALT, have not been tested with this product, use of such
E
accessories with this product could be hazardous. To reduce
the risk of injury, only D
WALT recommended accessories should
E
be used with this product.
If you need assistance regarding accessories, please contact the
manufacturer at 1-855-815-1171 or support@dewaltevcharger.com
6
Ensure that the prongs on the plug
the vehicle's charging port.
turned off.
If damaged, stop using the product
and switch the circuit breaker off.
Contact customer service.
Solution
Switch the circuit breaker off,
wait for 5 seconds and switch
it back on.
Wait for 30 seconds. If the fault
remains, switch the circuit
breaker off, wait 5 seconds and
switch it back on.
Switch the circuit breaker off,
wait for 5 seconds and switch
it back on.
Switch the circuit breaker off,
wait for 45 minutes and switch
it back on.
Switch the circuit breaker off
and let the product cool down
before switch it on again.
Switch the circuit breaker off,
wait for 5 seconds and switch
it back on.
Switch the circuit breaker off
and E11 Diode fault contact
customer service.
Switch the circuit breaker off,
wait for 5 seconds and switch
it back on.
Publicidad
