Publicidad
Idiomas disponibles
Idiomas disponibles
Read Operating
Instructions
Please
become
familiar
with all the instructions
and
warnings
before
operating
any pneumatic
tool.
Always
Wear Approved
Eye Protection
Impact
resistant
eye protection
should
meet
or exceed
the standards
set forth in ANSI
Z87.1,
Occupational
and
Educational
Eye and Face
Protection.
Look for marking
Z87.1
on your
eye protection
to ensure
that it is an
approved
style.
Hearing
Protection
is Recommended
Hearing
protection
should
be used when
the noise level
exposure
equals
or exceeds
an 8 hour time-weighted
average
sound
level of 85dBA.
Process
noise,
reflective
surfaces,
other tools
being
operated
nearby,
all add to the
noise level in a given work area. If you are unable
to
determine
your
noise
level exposure,
we recommend
the
use of hearing
protection.
Avoid
Prolonged
Expos ure to Vibration
Pneumatic
tools
can vibrate
during
use. Prolonged
exposure
to vibration
or very
repetitive
hand and arm
movements
can cause
injury.
Discontinue
the use of any
tool if you experience
tingling,
numbness,
discomfort
or
pain in your
hands
or arms.
You should
consult
your
physician
before
resuming
use of tool.
90PSI
Maximum
This tool is designed
to operate
at an air pressure
of 90
pounds
per square
inch gauge
pressure
(90 PSI)
maximum,
at the tool.
Use of higher
air pressure
can, and
may cause
injury. Also,
the use of higher
air pressure
places
the internal
components
under
loads and
stresses
they
were
not designed
for, causing
premature
tool failure.
NOTE:
THE AIR SUPPLY
SHOULD
BE CLEAN,
DRYAND
PREFERABLY
LUBRICATED.
FOR BEST RESULTS
DRAINTHE
MOISTURE
FROMYOUR
COMPRESSOR
DAILY.
FULL ONE YEAR WARRANTY
ON
CRAFTSMAN
AIR-DRIVE
TOOLS
If this Craftsman
tool fails to give complete
satisfaction
within one year from the date of purchase,
R ETUR N IT
TOTHE
NEARESTSEARS
STORE
INTHE
UNITED
STATES,
and Sears
will repair it free of charge.
If this
Craftsman
tool
is used for commercial
or rental
purposes,
this warranty
applies
for only 90 days from the
date of purchase.
This warranty
gives you specific
legal
rights,
and you may also have other
rights which
vary
from state to state.
Distributed
by Sears,
Roebuck
and Co., Dept. 817WA,
Hoffman
Estates,
IL 60179.
The Craftsman
Model 875.167061
Sand Blaster is
ideal for removing
rustand
paint from a variety of
surfaces.
Features
•
Compact
Design.
•
Maintenace
free.
•
Complete
with three tips.
Specifications
Tip Size .............................................................
4.8 mm or 3/16"
Weight. ..........................................................................
2.42 Ibs.
Sand Inlet Pipe Size ...........................................
13mm or 1/2"
Average
air consumption
........................................
9.5 SCFM
Suction Capacity. ........................................................
0.06 MPA
Recommended
hose size ...........................................
3/8" I.D.
Air inlet .........................................................................
1/4" NPT
Maximum
Air Press ure ..................................................
90 P S I
[ WARNIN ]
Some
dust
created
by power
sanding,
sawing,
grinding,
drilling
and other
construction
activities
contains
chemi-
cals
known
to cause
cancer,
birth defects
or other
reproductive
harm.
Some
examples
of these
chemicals
are:
Lead
from
lead
based
paint
crystalline
silica
from
bricks
and cement
and other
masonry
products,
and
arsenic
and chromium
from
chemically-
treated
lumber.
Your risk from those exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work
with approved safety equipment,
such as dust masks that
are specifically designed to filter out microscopic
par-
ticles.
P re-Operation
Before
the tool is connected
to the air supply,
clear the air
hose of accumulated
dust
and moisture
by running
air
freely
through
the air hose for 5-10 seconds.
Before
removing
a tool for service,
make sure
the air line is shut-
off at the compressor.
This will prevent
the tool from
operating
if the throttle
is accidently
engaged.
(2)
Installation
(See figure
1)
This tool is designed
to operate
at 90 psi. Lower
pres-
sure
(below
90 psi) will reduce
performance
of the tool
while
higher
air pressure
(over
90 psi) raises
the perfor-
mance
of the tool beyond
its rated capacity
and could
cause
serious
damage
to tool and user.
Always
use clean
dry air. Excessive
moisture
and dirt will
greatly
reduce
the life of any air motor. We recommend
the installation
of an in-line
filter-regulator-lubricator
as
close
to the tool as possible.
A 3/8" air hose is required up to a length of 8 ft. If more
length is required a 1/2" air hose should be used at the
compressor.
Attach a 3/8" whip hose for the remaining
4 - 8 ft. for flexibility. Be sure all hoses and fittings are the
correct size and tightly secured before using air tool.
Publicidad
