Serenco Powerhand SIN-100.2195 Instrucciones De Uso página 2

UK NL DE FR
Technical Data:
Type LED: SMD
Brightness: 500/1500/5000 Lumen
Battery: 7.3 V 8 Ah
IP rating: IP54
IK rating: IK07
Charging time: 6 hours
Run time: 2,5 ~ 10 hours
Working temperature: -20 ~ 50°C
Product dimensions: 120x120x910 mm
Power connection:
Use the lamp within places prescribed and governed by current regulations on workplaces and electrical systems.
Check that the plug fitted on the cable is suitable for the work environment, if it is not, it must be replaced by a
qualified electrician.
Main features:
• Rechargeable flood light with SMD LED technology
• SMD LEDs provide 500/1500/5000 Lumen
• Long life SMD LEDs (life span 100.000 hours)
• 110 ~ 120° swivel base
• Integrated tripod
• Low power consumption, low heat emission
• Lamp use is not affected by cold temperatures
• Cordless design improves safety, convenience and flexibility
• 7.3 V 8 Ah Li-Ion battery provides 2,5 ~ 10 hours constant light output
• Battery charge level indicator for easy monitoring
• IP54 rated
• IK07 rated
• CRI 70
• Broad 120° light spread
• Robust, shock resistant ABS + aluminium housing
Instructions for use:
• Charge the battery for at least 8 hours before first use
• To charge the lamp: connect the cable to the lamp directly, you will hear an audible click. Then connect the 100 ~ 240 V adapter plug into a wall
socket (to disconnect the charging cable, turn the adapter on the cord counter clockwise to unlock and remove the charging cable).
• The charge level indicator displays 25%, 50%, 75% and 100%, all 4 LEDs will lit up when 100% charging is complete
• The charge level indicator will show 1 flashing LED when charging is required, please re-charge in good time
• The work light is controlled by 2 buttons. 1. Power on/off 2. Colour temperature button. Push the ON/OFF button (1x) to turn the unit on 500 Lumen,
push the power button again shortly for 1500 Lumen, push the power button again shortly to set the lumen at 5000. Push the colour temperature
button to choose between 2 different colours, every time the button is pressed the next colour will lit up. Push the on/off button again to turn the
unit OFF
• Do not leave the battery in a fully discharged condition. Recharge the lamp at least once every 30 days. Always fully charge the battery to extend
the battery lifetime.
Instructions for corded use:
• The work light is controlled by 2 buttons. 1. Power on/off 2. Colour temperature button. Push the ON/OFF button (1x) to turn the unit on 1500
Lumen. Push the colour temperature button to choose between 2 different colours, every time the button is pressed the next colour will lit up. Push
the on/off button again to turn the unit OFF
Instructions for tripod setup/storage:
1. Open the top lever to loosen the extending tube, slide the extended tube to the desired height and close the lever to lock the extended tube
2. Open the bottom lever to loosen the extending tube, slide the extended tube to the desired height and close the lever to lock the extended tube (if the
lever is too loose or too tight, we have a standard Phillips screw which allows you to tighten or loosen the locking mechanism at your desired setting)
3. To set up the legs, simply pull out all legs, until they lock into their fixed place
4. When you have finished, just simply open the top lever to loosen the extending tube, slide it back into the starting position and lock it again
5. Open the bottom lever lo loosen the extending tube, slide it back into the starting position and lock it again
6. To close up the legs, simply slide the release button downwards, to unlock the mechanism that is holding the leg into place, while holding the button
downwards begin pulling the legs to the starting position, do this 3 times to have al legs, folded up (if the legs are locked, just wiggle the legs a bit,
to disengage the locking mechanism, if you pull/push to hard, you may damage the mechanism)
Use lamp without tripod:
The lamp can also be used without the tripod. Unscrew the lamp by turning it counter-clockwise, and attach the lamp to any magnetic surface (with 4
integrated magnets). After use and to store, re-attach the lamp by screwing it back on to the tripod clockwise.
Accessories and spare parts:
5 m cable included H05RN-F 2x 0.75 mm2
Use only accessories and spare parts approved by the manufacturer
Caution:
• Avoid looking directly into the beam
• Do not use the lamp near open flames
• Switch off the lamp when not in use
• Only use this lamp for the purpose it is designed to, all modifications are strictly prohibited
• Should any cable be damaged, it must be immediately replaced with one of the same type
• When plugging the charger into a suitable mains supply, always check that the device is in good condition, and does not appear damaged as this
may impair safety
Warranty/Service:
• 12 months from the date of the purchase – Proof of purchase is required to make any warranty claim
• The warranty does not apply in case of damage to the device due to negligent / improper use or accidental damage
2
ES
Lumen Laser class I
Protection class III
EAN: 8717775514893
Colour temperature: 4000/7000 K
Weight: 4.7 kg
Hydrocarbon and UV resistant
Technical data charger:
Voltage: AC 100 V ~ 240 V
Frequency: 50/60 Hz
Charger output voltage: 8.4 V DC, 3 A
Tripod +
detachable lamp
98 N
91 cm