Descargar Imprimir esta página

Hotpoint HI 5030 WEF Guía Rápida página 2

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 4
EN
ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020.
Note for Test Laboratories: For information on comparative EN testing conditions, please send an email to the following address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) Values given for programs other than the program Eco are indicative only. The actual time may vary depending on many factors such as temperature and
pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options and sensor cali-
bration. The sensor calibration can increase program duration up to 20 min.
OPTIONS AND FUNCTIONS
OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL). If an option is not compatible with the selected
program (see PROGRAMS TABLE), the corresponding LED flashes rapidly 3 times and beeps will sound. The option will not be enabled.
ZONE WASH 3D - Option works with one rack at once. In particular,
we recommend to use it with Mixed and Intensive cycles - thanks to
the additional 3D water jets placed on the bottom o the cavity, ZONE
WASH 3D option allows to save energy or to increase the washing
performance of the dishwasher.
DELAY - The start time of the program may be delayed for a period of
time between 1 and 12 hours.
The DELAY function cannot be set once a program has been started.
TABLET (Tab) - If you use powder or liquid detergent, this option
should be off.
LOADING THE RACKS
CUTLERY RACK
(loading example for the
cutlery rack)
The third rack was designed
to house the cutlery.
CLEANING AND MAINTENANCE
CLEANING THE FILTER ASSEMBLY
A
In case you find foreign objects (such as broken glass, porcelain, bones, fruit seeds
etc.) please remove them carefully.
NEVER REMOVE the wash-cycle pump protection (black detail) (Fig 4).
2
UPPER RACK
FLAPS WITH
ADJUSTABLE
(loading example for the
upper rack)
Load delicate and light
dishes: glasses, cups,
saucers, low salad bowls.
B
A
C
Please scan the QR code on your product in order to have more detailed information.
OPERATION INDICATOR - A LED light projected on the floor indicates
that the dishwasher is working.
One of the following operating modes can be selected:
a) Disabled function.
b) When the cycle starts the light goes on for few seconds, stays off during
the cycle and flashes at the end of the cycle.
c) The light stays on during the cycle and flashes at the end of the cycle
(default mode).
ActiveDry - is a convection drying system which automatically opens the
door during/after the drying phase to ensure exceptional drying perfor-
mance every day. The door opens at a temperature that is safe to your
kitchen furniture.
FOLDABLE
POSITION
(loading example for the
lower rack)
CLEANING THE SPRAY ARMS
To remove the upper spray arm,
turn the plastic locking ring in a
clockwise direction.
CAPACITY: 14 standard place-settings
LOWER RACK
For pots, lids, plates,
salad bowls, cutlery
etc. Large plates and
lids should ideally be
placed at the sides to
avoid
interferences
with the spray arm.
The lower rack has
tip-up
supports
which can be used
in a vertical position
when arranging pla-
tes or in a horizontal
position (lower) to
load pans and salad
bowls easily.
More information in the Daily Reference Guide on website.
Quick Guide
ZONE WASH 3D
Zone Wash 3D uses addi-
tional water jets located
both: in the lower and
upper part of the di-
shwasher (marked with
orange color) to wash
more intensively heavily
soiled items by increa-
sing water coverage on
dishes.
The lower spray arm may
be removed by pulling it
upwards.

Publicidad

loading

Este manual también es adecuado para:

859991594220