Holmes Blizzard 32510126 Manual De Instrucciones

Instruction Manual
Air Circulator Fan
PLEASE READ AND SAVE THESE IMPORTANT INSTRUCTIONS
C L E A N I N G / M A I N T E N A N C E
FAN CLEANING
• Always unplug the fan before cleaning.
• Do not allow water to drip on or into the fan
housing.
• Use only a soft cloth moistened with a mild soap
solution.
• Do not use harsh chemicals such as gasoline,
thinner or benzene as a cleaner.
• Do not attempt to remove the fan blade.
FAN HEAD AND BASE CLEANING
Using a soft, moist cloth, with or without a mild soap
solution, carefully clean the fan base and head. Use
CAUTION around the housing area.
Do not allow the motor or other electrical components to
be exposed to water.
FAN STORAGE
• Store the fan in a clean, dry location between seasons
or when not in use for an extended period of time.
• Keep the fan protected from dirt and dust during
storage.
NOTE: This fan can also be used during the cold winter
season to circulate warm air throughout your home.
For inquiries regarding recycling and proper disposal
of this product, please contact your local waste
management facility.
I M P O RTA N T S A F E T Y I N S T R U C T I O N S
Cool Grey Item: 12518
Misty Blue Item: 12820
Model: 32510126
When using electrical appliances, basic safety precautions
should always be taken including the following:
1. Read all instructions before using this appliance.
2. Use fan only for purposes described in the instruction
manual.
3. To protect against electrical shock do not immerse unit,
plug or cord in water or spray with liquids and plug
the appliance directly into a 120V AC electrical outlet.
4. Close supervision is necessary when any appliance is
used near children.
5. Not intended for use by children.
6. Unplug from outlet when not in use, when moving fan
from one location to another, and before cleaning.
7. Avoid contact with moving parts.
8. Do not operate in the presence of explosive and/or
flammable fumes.
9. To avoid fire hazard, NEVER place the cord under rugs
or any parts near an open flame, cooking or other
heating appliance.
10. Do not operate any appliance with a damaged cord
or plug after the appliance malfunctions, or has been
dropped/damaged in any manner. Discard fan or
contact customer service.
11. Do not run cord under carpeting. Do not cover cord
with throw rugs, runner, or similar coverings. Do not
route cord under furniture or appliances. Arrange cord
away from traffic area and where it will not be tripped
over.
12. The use of attachments not recommended or sold by
the appliance manufacturer may cause hazards.
PLEASE READ AND SAVE THESE IMPORTANT
SAFETY INSTRUCTIONS
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than
the other). To reduce the risk of electric shock, this plug is intended to
fit in a polarized outlet only one way. If the plug does not fit fully in
the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician to install the proper outlet.
USER SERVICING INSTRUCTIONS
Follow these instructions to safely and correctly care for this fan.
REPLACEABLE FUSE
If the (2.5 Amp, 125 Volt) replaceable fuse blows, please visit our website at www.getholmesfans.com for information
on how to order a new fuse. Follow the below instructions to replace the fuse on the plug.
REPLACING THE FUSE
1. Unplug the fan.
Grasp plug and remove from the receptacle or other outlet device.
NOTE: Do not unplug by pulling on cord.
2. Open fuse cover, located on the top of the plug, by using your thumb or a flathead
screwdriver to slide the cover towards the prongs.
NOTE: Ensure the fuse cover is completely open before attempting to remove fuse.
3. Remove fuse carefully by using a small screwdriver to pry it from the compartment at
the metal ends of the fuse. (See Figure 2)
4. Place plug on a solid, flat surface. Insert new 2.5 Amp, 125 Volt fuse into fuse
compartment. Use a small screwdriver to secure the metal ends of the fuse into the
compartment.
CAUTION: Risk of fire. Replace fuse only with 2.5 Amp, 125 Volt fuse.
5. Slide fuse cover closed completely.
NOTE: If fuse cover is difficult to close, make sure the fuse is completely secured in place by pressing on metal ends
of the fuse.
CAUTION: Risk of fire. Do not replace the attachment plug. It contains a safety device (fuse) that should not be
removed. Discard product if the attachment plug is damaged.
13. Do not let the cord hang over the edge of a table,
counter or come in contact with hot surfaces or leave
exposed to high traffic areas.
14. Do not use outdoors.
15. To disconnect, grip plug and pull from wall outlet.
Never yank on cord.
16. Always use on a dry, level surface.
17. Do not operate fan until fully assembled with all parts
properly in place.
18. This product is intended for household use ONLY and
not for commercial or industrial applications.
19. WARNING: To reduce the risk of electrical shock and
injury to persons, do not use in window.
20. WARNING: To reduce the risk of fire or electric
shock, do not use this fan with any solid-state speed
control device.
21. WARNING: To reduce the risk of fire, electric shock
or injury to persons, do not use replacement parts that
have not been recommended by the manufacturer
(e.g. parts made at home using a 3D Printer).
22. This fan employs overload protection (fuse). A blown
fuse indicates an overload or short-circuit situation.
If the fuse blows, unplug the product from the outlet.
Replace the fuse as per the user servicing instructions
(follow product marking for proper fuse rating) and
check the product. If the replacement fuse blows, a
short circuit may be present and the product should be
discarded or contact customer service.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
M A I N T E N A N C E
Figure 2
Fuse
Fuse cover
Metal ends
O P E R AT I O N
ASSEMBLY WALL MOUNTING INSTRUCTIONS
This fan comes completely assembled and is ready for use.
This fan can be wall mounted and is designed to operate
from various positions while wall mounted, mounting
OPERATING INSTRUCTIONS
screws not included.
1. Set the fan base on a dry, level surface. 1. After selecting a suitable location on the wall, use the
2. Make sure the Speed Control Knob (E) is in the OFF corresponding mounting location guide below to ensure
(0) position.
proper placement.
3. Plug cord into any standard 120 volt AC outlet.
2. Use the holes below as a guide and mark the correct
4. To adjust the speed, turn the Speed Control Knob (E)
place where the screws will be inserted. Consult with
to the desired setting, 1-2-3.
a hardware or Home Center Professional for the best
TILT ADJUSTMENT
screws for your type of wall.
3. Secure the screws almost all the way into the wall using
Gently move the fan head up or down manually to the
a screwdriver.
desired angle.
4. Line up the holes on the back of the unit with the
screws to hang the fan. Make sure the screws are
secured into the wall before carefully placing the fan
on them.
MOUNTING LOCATION GUIDE
Use this diagram to help properly line up screws.
FIGURE 1
C
B
A
A. Front Grill
B. Rear Grill
C. Fan Blade D
D. Base
E. Speed Control Knob
F. Motor Housing
WA R R A N T Y I N F O R M AT I O N
3 YEAR LIMITED WARRANTY
This device has a limited warranty of 3 years from the original date of purchase against workmanship and defects in
material. If under normal use, your product fails to operate, please contact our customer service department at
info@getholmesfans.com. A refund or replacement will be provided to you with proof of purchase. Star Elite Inc. may
deny claims of damage caused by misuse or modifications of this product.
Warranty Service
Contact our customer service at www.getholmesfans.com/en/contact-us
or info@getholmesfans.com or 1-866-769-3166 (8:30 am - 5:00 pm EST) Monday-Friday.
Our team will be happy to assist.
www.getholmesfans.com
© 2023 Sunbeam Products, Inc. All rights reserved.
HOLMES ® and BLIZZARD ® are registered trademarks of Sunbeam Products, Inc. used under license.
Distributed by Star Elite Inc., Montreal, Canada H3B 3X9
SEH027-101123
Printed In China
E
F