Publicidad
Idiomas disponibles
Idiomas disponibles
Mounting instructions for waterpipe installers:
Points 1 to 5 and 19 to 24:
Important: Read these instructions thoroughly before
installing the appliance. Determine the precise position in
the salon with the salon owner and the installation
specialist.
•
The shampoo station is intended for operation in
clean and dry rooms at normal room temperature.
•
In the water supply system only original components
supplied by the manufacturer must be used.
•
The house installation must be equipped with a
pressure reducing valve. Recommended water
pressure for the shampoo station: approx. 3 – 5 bar.
•
The new set of hoses supplied with the unit must be
used. Old hoses must not be used.
Points 1 - 5 must be completed according to
"Planning information for plumber" before the
shampoo station is delivered:
1.
We recommend to provide the supply lines with a
central shut-off device.
If the system is operated without a suitable shut-off
device, the angle valves must be closed at the end
of business hours.
2.
Place the mounting template at the determined
position and use it to drill the required holes.
Observe the notes on the mounting template!
3.
Make the holes for cold water (K), hot water (W)
and waste water (A).
4.
Pay close attention to the position and spacing of
the supply lines and the drain pipe (see installation
template).
5.
Height of the connecting pipes and drain pipe:
½" pipe: 50 mm above finished floor 40 mm dia.
Drain pipe: 50 mm above finished floor
Splendor Edition / Shiatsu MO B+R
GB
Mounting instructions for appliance fitters:
Points 6 to 18 and 29 to 32:
6.
Align the installation template on the floor according to
the on-site water connections. To do this, cut the location
of the water connections on the template crosswise in
order to be able to align the template flat on the floor.
Mark 4 attachment points for the shampoo station and
drill holes for Ø 10 mm dowels in the floor. Insert dowels.
7.
Unscrew the support rails (A) of the shampoo station
from the pallet. Only lift the shampoo station by the belt
loops (B) of the support rails and lift it off the pallet and
place it near the water connections.
8.
Remove the inspection cover on the back. To open,
press the chrome-plated button and pull to release the
magnetic connection (illustr. 2)
9.
Only lift the shampoo station by the belt loops of the
support rails and place it over the waste water pipe, the
water connections and the attachment points.
10. Pull the cable with the mains plug (C) outwards at the
back. To do this, open the cable ties. (illustr. 1)
Plug the plug into wall plug socket for provisional
electrical connection.
11. Take out the backrest pad. To do this, tilt the washbasin
all the way up. Then grab between the seat and the back-
rest, pull the backrest up, swing it forward and remove it
Upwards (ilustr. 5)
12. Unhook the seat cushion. To do this, extend the leg rest
approx. 2/3, press the seat pad back firmly to release the
locking bracket from the frame. Swivel the seat cushion
up and tilt it forward (illustr. 6).
13. On the inside of the frame, loosen the 4 transport screw
connections from the support rails and pull out the
support rails under the shampoo station. To remove the
front support rail, grasp the unit by the legrest frame, to
remove the rear support rail, grasp the cover plate under
the basin.
14. Only for the "mains cable with plug" version:
Define the side of the cable outlet on the shampoo
station (left or right). Cut out the lower trim in the rear
area (80 mm from the rear edge) according to the cable
cross-section (illustr. 3).
The cut-out must be large enough so that the mains
cable is not crushed!
Lead the cable with mains plug in the recess to the
outside.
page 1 of 3
Publicidad
