Publicidad
Idiomas disponibles
Idiomas disponibles
PRODUCT
SPECIFICATIONS
Serial Number:
Date of Purchase:
Gasoline
Capacity
/ Type:
1.5 Quarts
(Unleaded
Regular)
Oil Type (API-SF-SJ):
SAE 30 (above
32°F); SAE 5W-30
(below
32°F)
Oil Capacity:
20 Ounces
Spark
Plug (Gap:
.030")
Champion
RJ19LM
or J19LM
Blade Bolt Torque:
35-40 ft. Ibs.
The model
and serial numbers
will be found
on a decal on the rear of the mower
housing.
Record
both serial number and date of purchase
in space provided
abov,
LAWNMOWER
Always observe safety rules when perform-
ing any maintenance.
TIRES
• Keep tires free of gasoline, oil, or insect
control chemicals which can harm rubber.
* Avoid stumps, stones, deep ruts, sharp
objects and other hazards that may cause
tire damage.
BLADE CARE
For best results, mower blade must be
kept sharp. Replace bent or damaged
blades.
TO REMOVE BLADE
1. Disconnect spark plug wire from spark
plug and place wire where it cannot
come in contact with spark plug.
2. Turn lawn mower on its side. Make
sure air filter and carburetor are up.
3. Use a wood block between blade and
mower housing to prevent blade from
turning when removing blade bolt.
NOTE; Protect your hands with gloves
and/or wrap blade with heavy cloth,
4. Remove blade bolt by turning counter-
clockwise.
5. Remove blade and attaching hard-
ware (bolt, lock washer and hardened
washer).
NOTE: Remove the blade adapter and
check the key inside hub of blade
adapter. The key must be in good condi-
tion to work properly. Replace adapter if
damaged.
TO REPLACE
BLADE
1. Position
the blade adapter
on the
engine
crankshaft.
Be sure key in
adapter
and crankshaft
keyway
are
aligned.
2.
Position
blade
on the blade adapter
aligning
the two (2) holes
in the blade
with the raised
lugs on the adapter.
3.
Be sure the trailing
edge of blade
(opposite
sharp
edge) is up toward
the engine.
4.
Install the blade bolt with the lock
washer
and hardened
washer
into
blade adapter
and crankshaft.
5.
Use block of wood between
blade and
lawn mower
housing
and tighten
the
blade bolt, turning
clockwise.
• The
recommended
tightening
torque
is
35-40 ft. Ibs.
IMPORTANT:
Blade bolt is grade 8 heat
treated.
TO SHARPEN
BLADE
NOTE:
We do not recommend
sharpen-
ing blade - but if you do, be sure ttle
blade is balanced.
Care should
be taken to keep the blade
balanced.
An unbalanced
blade
will
cause
eventual
damage
to lawn mower
or engine.
• The blade can be sharpened
with a file
or on a grinding
wheel. Do not attempt
to sharpen
while on the mower.
° To check b{ade balance,
drive a nail
into a beam or wall. Leave about
one
inch of the straight
nail exposed.
Place
center
hole of blade over the head of
the nail. If blade is balanced,
it should
remain
in a horizontal
position.
If either
end of the blade moves
downward,
sharpen
the heavy end until the blade
is balanced.
Blade adapter _Crankshaft
Key--..._,
_
_
keyway
Lockwasher
111"%_
/
J
Blade /
_,_,_%'._
>'_'/c_
_
\
\
N_
I J- \_/
;rank
bait Hardene_l"
'
" "_"
"
washer
Trailin edge
Blade adapter
11
Publicidad
