Ryobi CMD-1802M Manual De Utilización página 10

GB
F D E
RULES FOR SAFE OPERATION
If under abusive conditions, liquid is ejected from
■
the battery, avoid contact. If this accidentally
occurs, flush with water. If liquid contacts eyes
additionally, seek medical help.
Do not place battery tools or their batteries near
■
fire or heat. This will reduce the risk of explosion and
possibly injury.
WARNING
Batteries vent hydrogen gas and can explode in
the presence of a source of ignition, such as a
pilot light. To reduce the risk of serious personal
injury, never use any cordless product in the
presence of open flame. An exploded battery can
propel debris and chemicals. If exposed, flush
with water immediately.
SPECIFICATIONS
Model
Voltage
Chuck
Switch
No load speed
(drill mode):
- Lo speed
- Hi speed
No load speed
(impact mode):
- Lo speed
- Hi speed
Max. Torque
Weight - incl.
battery pack
Battery pack (not included)
- 1.7Ah
Charger (not included)
FEATURES
1. Keyless chuck
2. Switch trigger
3. Direction of rotation selector (Forward/Reverse)
4. Screwdriver bits
5. Battery pack (not included)
6. Battery indicator
7. Latches
8. Auxiliary Handle
9. Drill bit (not included)
10. Depth Gauge Rod
11. Torque adjusting Ring
All manuals and user guides at all-guides.com
I P NL S
CMD-1802M CMI-1802M
18 V 18 V
13 mm 13 mm
Variable speed Variable speed
-1
0 - 370 min 0 - 390 min
-1
0 - 1350 min 0 - 1350 min
- 0 - 5070 min
- 0 - 17550 min
35 Nm 35 Nm
2.3 kg 2.5 kg
BPP-1817 BPP-1817
BC-1800/ BC-1800/
BC-1815-S BC-1815-S
DK N FIN GR H
English
OPERATION
TO INSTALL BATTERY PACK (NOT INCLUDED)
Lock switch trigger on your drill by placing the
■
direction of rotation selector in center position.
See Figure 6.
Place battery pack in your drill. Align raised rib on
■
battery pack with groove inside drill. See Figure 2.
Make sure the latches on battery pack snap in place
■
and battery pack is secured in drill before beginning
operation.
TO REMOVE BATTERY PACK (NOT INCLUDED)
Lock switch trigger on your drill by placing the
■
direction of rotation selector in center position.
See Figure 6.
Locate latches of battery pack and depress to release
■
battery pack from your drill. See Figure 2.
Remove battery pack from your drill.
■
ADJUSTING THE AUXILIARY HANDLE
(For CMI-1802M)
See Figure 3.
Follow these steps to adjust the auxiliary handle.
Loosen the auxiliary handle by turning the knob
■
-1
counterclockwise.
-1
Rotate the auxiliary handle to the desired location.
■
Tighten the auxiliary handle securely by turning the
■
-1 knob clockwise.
-1
ADJUSTING THE DEPTH GAUGE ROD
(For CMI-1802M)
See Figure 4.
Follow these steps to adjust the depth gauge rod.
Lock the trigger switch by placing the rotation selector
■
in the center position.
Loosen the auxiliary handle by turning the knob
■
counterclockwise.
Adjust the depth gauge rod so that the drill bit
■
extends beyond the end of the rod to the required
drilling depth.
Tighten the auxiliary handle by turning the knob
■
clockwise.
ADJUSTING THE TORQUE
See Figure 5.
The tool is equipped with an adjustable torque clutch for
driving different types of screws into different materials.
Adjust the torque as necessary.
6
CZ RUS RO PL SLO HR TR