Publicidad
Idiomas disponibles
Idiomas disponibles
Figura a
a.1
Figura b
AFUERA
Figura e
Vista trasera
Figura f
f.1
Figura h
10
Page 8
Página 8
Copyright © 2024 O3 Pure es una división de Pure Energy LLC
a.2
a.3
WALL VALVES
ADENTRO
CALIENTE
FRÍO
Dejar la línea
de agua
caliente
existente como
se instaló
originalmente
X
Ozone Level
o3pure.com
f.2
7
8
a.4
a.5
Figura c
Level Guide Line
Center Line
7
Forward
2
to remove
Level
1"
Up
1
5
6
INSTALL ANCHORS
OR SCREWS HERE
3
8
Level template and
8 in. (20 cm)
Center with
Washing Machine
mark on wall. (1 of 2)
O3 Pure
Oxidizer
4
OPTIONAL STEPS
TO REMOVE COVER
1/4 in.
6.35 mm
5
In and hold
1. Place Quick Install Mounting Template on wall anywhere within 5'
3. Remove the cover from your O3 Pure by SLIGHTLY pressing the tabs
4. Place the O3 Pure against the wall so that the protruding screws
MIN
of your washing machine. Leveled and centered above your washing
on each side of the cover inwards.
5
While gently holding the tabs
slip through the "keyholes"
8
in the back of the unit. Gently slide
INSTALL
machine usually looks best.
1
in, lift the cover up 1 inch (2.54 centimeters)
6
and then straight
the unit down into the lock position of the keyholes. You can now
out toward you.
7
There is a quick disconnect for the Ozone
tighten the two screws to hold the unit firmly in place. DO NOT over
2. Place marks on the wall using template. Remove template. Drill 1/4"
(6.35mm) holes for the anchors
2
or if installing directly into a
Level Button. It is located behind the cover and can be used to set
tighten the screws. Reconnect Ozone Level Button. Replace the cover
the cover down for easier installation.
on the O3 Pure.
stud just use the screws and predrill 1/16" (1.6mm) holes. Install the
provided anchors and screws
3
leaving the screws protruding
•
•
from the wall by about 1/4 inch.
4
Simply hang the O3 Pure on
DO NOT connect hot water to your O3 Pure system.
Ozone Level Button:
•
the screws. If a snugger fit is needed, remove the O3 Pure, slightly
– No Light: Allows the unit to run without engaging the ozone generator. The
tighten the screws and rehang the unit or optionally remove the
Performance is best when washing with cold water only.
•
Photo Catalytic Oxidizer will still operate and provide a very mild Cleaning Action.
front cover in the next steps.
Use little or preferably no detergent, bleach and fabric
Green Light:
–
Recommended for general washing and everyday use.
softener.
Blue Light:
–
Runs at full ozone output. For whites and deep cleaning colors.
8 pulgadas
e.1
Vista interior
Figura g
Ozone Level
5
6
10b
9
O3 Pure
Oxidizer
2
a.6
Experience the Natural Purifying Benefits of Oxygen.
Eco Laundry System
Quick Step Installation Guide on backside.
Figura d
PASOS OPCIONALES PARA
RETIRAR LA CUBIERTA
Level Guide Line
WALL VALVES
OUT
IN
INSTALL ANCHORS
HOT
COLD
OR SCREWS HERE
8
11
10
9
Level template and
mark on wall. (2 of 2)
Leave existing
hot water line
as originally
installed.
5. Turn off cold water valve. Disconnect the cold hose from the washing machine
9
and connect to the cold water inlet of the O3 Pure.
Tighten the hose to
the inlet fitting. Do not over tighten, and do not use thread tape or sealer.
6. Connect one end of the provided hose to the water outlet of the O3 Pure and
the other end to the cold water inlet of the washing machine.
10
Properly
tighten both ends of the hose, but again do not over tighten and don't use
thread tape.
7. Plug the power adapter into the DC adapter plug-in on the side of the O3 Pure unit
and then plug the adopter into the wall outlet.
11
8. SLOWLY turn the COLD WATER Valve back on and check for any leaks.
9. Set the wash cycle on your washing machine to COLD WATER wash and
COLD WATER rinse.
1 pulg.
arriba
d.1
Hacia adentro y mantener
O3 Pure
Oxidizer
Ozone Level
o3pure.com
o3pure.com
g.1
4
10a
3
1
a.7
8 Deslizar hacia
adelante para retirar
d.2
Ozone Level
o3pure.com
g.2
Publicidad
