Publicidad
Idiomas disponibles
Idiomas disponibles
1. SAFETY
The device is developed according to the regulations
and is subject to continuous quality control.
These performances require strict compliance with
the installation and maintenance rules contained
in these operating manual and in particular the
indications marked by:
Meaning
DANGER
This term defines a high risk of
danger, which can lead to death or
serious injury, if not avoided.
NOTICE
This term characterises dangers to
the machine and its proper operation.
Warning of a general danger.
The danger is specified by indications
given in the table.
This symbol characterises dangers
associated with the voltage and
provides information on voltage
protection.
Please refer to installation standard EN 12056-4.
Failure to comply with this operating and installation
manual will result in the loss of warranty rights and
rights to damages.
Disconnect electrical power before
working on the unit!
2. DESCRIPTION
2.1 APPLICATIONS
Your compact macerator allows the discharge of waste water into
a Ø32 mm pipe.
This appliance is for domestic use only.
Do not use for commercial or industrial applications.
The device has a high performance level, and is safe and reliable,
provided all the rules for installation and maintenance in this notice
are strictly followed.
2.2 OPERATING PRINCIPLE
Your wall-hung toilet is equipped with a pump shredder intended
to grind up paper and organic waste.
Its system is installed in a wall-hung ceramic bowl with a frame
without a cistern.
2.3 TECHNICAL DATA
Maximum vertical discharge
Maximum horizontal discharge
Nominal power
Frequency
Voltage
Electrical class
Protection index
Net weight
2.4 PUMP CURVE
2
See figure
.
2.5 VERTICAL PUMPING/HORIZONTAL PUMPING
3
See figure
.
2.6 SCOPE OF SUPPLY
4
See figure
.
2.7 DIMENSIONS
1
See figure
.
3. INSTALLATION
The fitting and working of your appliance must meet local
regulations and the EN 12056-4 standard.
IMPORTANT
Before installation, check that the load-bearing wall can support
the weight of the appliance (max. pull-out force = 120 kg).
• Locate the fixing holes for the toilet bowl on the frame,
depending on the bowl height chosen:
• Select the height of your toilet bowl according to these values:
• Figure
the frame according to the following dimensions : L = 45 mm + X
(X being the thickness of your cladding, plasterboard, tiles, box ...).
• Place the lock nut on the back of the frame and tighten the
assembly.
• Figure
rods.
• Figure
holes in the frame.
• Figure
below.
• Mesure the distance Y between the two retaining anchors.
• Figure
K
Connection of a handbasin (option). Figure
• Saw the closed inlet.
• Insert the hose
• Figure
frame (distance from the wall: 100 mm) and the angle bracket
(not supplied). Provide at least 3 anchoring points at the feet, 2 of
which must be on the wall side.
• Figure
• Fit the appropriate fixings according to your wall (use 8x120 mm
lag bolts; these parts are not supplied).
• Figure
• Figure
wall and the edge of the frame; the distance between the wall and
the edge of the frame must be 100 mm.
• Check the alignment between the wall and the frame, the frame
must be parallel to the wall.
• Figure
See figure
The water supply is in the upper part of the frame.
The water supply must be connected to a 14/16 copper pipe with a
20/27 male threaded connection (not supplied).
Secure the copper pipe with a clamp to prevent any movement
3 m
when connecting the device.
30 m
It is essential to install an accessible 1/4 turn shut-off valve on the
550 W
water inlet to facilitate any intervention
50-60 Hz
220-240 V
See figure
I
Discharge the waste water with a PVC pipe Ø32 mm.
IPX4
Maintain a slope of 1% on all horizontal sections.
43 kg
• Install the discharge pipe at a distance from the floor of :
• Secure the discharge pipe with a clamp.
15
3.1 PREPARATION OF THE SUPPORT FRAME
– Seat height 475 mm = top fixing holes;
– Seat height 445 mm = middle fixing holes;
– Seat height 415 mm = bottom fixing holes.
5.1
. Insert the threaded rods
5.2
. Screw the stainless steel inserts
5.3
. Insert the retaining brackets
3.2 PREPARATION OF THE TOILET BOWL
6.1
. Insert the retaining anchors
6.2
. Prepare the connection by attaching the elements
to the hose. Secure with hose clamps
L
over the inlet, securing with a hose clamp
3.3 FIXING OF THE SUPPORT FRAME
7.1
. Use a pencil to mark the intended location of the
7.2
. Remove the support frame and drill.
7.3
. Attach the angle bracket.
7.4
. Use the nuts to adjust the dimension between the
7.5
. Attach the support frame.
3.4 WATER SUPPLY
8.1
.
3.5 SEWAGE DISCHARGE
8.2
.
– 340 mm for a bowl 475 mm from the floor (1) ;
– 310 mm for a bowl 445 mm from the floor (2) ;
– 280 mm for a bowl 415 mm from the floor (3).
EN
A
into the fixing holes of
B
onto the threaded
C
into the mounting
D
into the holes, from
J
.
6.3
:
I
.
Publicidad
