Publicidad
Idiomas disponibles
Idiomas disponibles
INSTRUCTIONS ON ASSEMBLY AND USE
EN
CONGRATULATIONS ON PURCHASING THIS PRODUCT!
Please read these instructions carefully. The instructions are an integral compo-
nent of the product. Therefore, please store them and the packaging carefully in
case questions arise in the future. Please always include these instructions when
handing on the product to a third party. This product must be assembled by an
adult. This product is designed for private/domestic use only. This product is not
designed for commercial/industrial use. The use of the product requires certain
capabilities and skills. Always adjust according to the age of the user and use for
the purpose it has been designed for.
TECHNICAL SPECIFICATIONS
Item:
Nest Swing 110
Item No.:
72148, 72156
Maximum carrying capacity:
100 kg
Dimension:
110 cm Ø
Purpose:
Device powered by muscle power, for swinging
in a sitting or lying position.
Minimum user age:
3 years
If you have assembly problems or would like further information on the product,
we have all you need and more at http://www.hudora.de/.
CONTENTS
1 x Nest swing (cf. parts list on page 2) | 1 x These instructions
Other parts which may be included with the delivery in some circumstances are not
required.
SAFETY INSTRUCTION
• WARNING! Only for domestic use.
• WARNING! To be used under the direct supervision of an adult.
• WARNING! Not suitable for children under 36 months. Danger of falling!
• WARNING! Not suitable for children under 36 months due to long cords! Stran-
gulation hazard.
• WARNING! Suitable for outdoor and indoor use!
• The owners of the swing as well as the competent supervisory personnel are
responsible for ensuring that all users follow the instructions in the operation
manual.
• Do not make any technical modifications.
• Changes to the original product must only be carried out according to manu-
facturer specifications.
• No one is permitted to gain access to the swing area during use.
• Never stand or kneel on the swing.
• Always hold yourself firmly with both hands.
• No objects of any kind must be in the vicinity of the swing zone (trees, walls,
fences, clotheslines).
• Make sure that you have a safety clearance of at least 2 m (front and back)
beyond the maximum reach of the swing and make sure the ground is level
and shock absorbing (e.g. grass) without any sharp edges or pointed objects,
obstacles, inclines, levels, steps or hard surfaces (e.g. concrete) etc.
• Clearance to stationary components on the side, such as the swing scaffol-
ding must be at least 40 cm.
• Swinging components, such as a neighboring swing must be placed at a di-
stance of at least 60 cm.
• Maximum raised height must not exceed 2.5 meter as measured from the
ground.
• In idle mode, the swing must be at least 40 cm and maximally 60 cm from the
ground.
• You should never install a swing in such a way that the user could be blinded
by sun rays.
• The self-locking effect of the self-locking nuts or else lacquer can subside
after repeated loosening and tightening of the connection elements.
• When permanently irradiated with UV light, the material ages significantly fa-
ster. To avoid premature aging and thereby extend the service life, you should
always store the product in a dry and dark place when not in use. Do not
permanently expose the product to wind, moisture, extreme temperatures or
sunlight.
All images are examples of the design.
ASSEMBLY INSTRUCTION
Prior to installation, carefully select and check the location where you will install
the swing. Please make sure that the swing carrier is adequately stable. Please
also take into account that swinging produces centrifugal forces that can put a lot
of strain on the swing carrier. Please consult an expert (statics expert, architect,
carpenter) and ask how much load your swing carrier can tolerate.Suspension
connectors shall be of a design that will prevent unintentional disconnection.
Remove the parts from the packaging and check that they are complete. Check
that parts 2, 3, 4 and 7 are already assembled as in fig. A. Now spread the nest
(5) on the ground. Insert part of the foam-covered tube frame (1) into each of
the four side loops (fig. B), then insert the parts into one another. Ensure that
one narrow and one wide tube end is put together in each case. Feed the screw
hooks (2) from above into the tubular frame and tighten the nuts firmly (simpli-
fied illustration in fig. C. See also safety notes!) In order to provide for a firm and
secure fit of the nut screw, please screw at least the entire height of the nut on
the screw hooks (2). The torque for tightening the nut should be between 8 and
10 nm. You can now hang the nest swing from a suitable swing frame using the
retaining rings (3).
HANGING DEVICE AND ADJUSTMENT
The hanging points must be at least as far apart as the swing seat + 100mm.
The swing is packaged with two ropes and adjustment eyelets (4), so that the
height of the swing can be variably aligned with any suitable hanging device. The
swing rope (7) can be lengthened or shortened by pushing or pulling it through
the adjustment loops (4). The hanging swing can now be individually adjusted.
No one should sit on the swing while making the adjustments. When extending or
reducing the length of the swing ropes please make sure that the ropes remain
equally long at all times. If the lengths of the ropes differ, this will lead to circular
pendulum movements of the swing. Make sure that swing is set up in such a way
that the person using the swing cannot reach the ground with the tips of his or
her toes. If in doubt, perform a few gentle test swings.
MAINTENANCE AND STORAGE
Use a dry or damp cloth only to clean the product; do not use special cleaning
agents! Check the product for damage or traces of wear and tear before and after
each use. Do not make any structural changes. For your own safety, please use
original spare parts only. These can be sourced from HUDORA. If parts become
damaged or if sharp edges or corners should develop, the product may not be
used any more. If in any doubt, please contact our service team (http://www.
hudora.de/service/). Store the product in a safe place where it is protected from
the elements, cannot be damaged, and cannot injure anyone.
You should also replace all the plastic parts after a maximum of 5 years to pre-
vent a possible failure of these parts.
Check the product for damage or traces of wear and tear before and after each
use.
We also recommend before each use:
• to check for the firm sitting of nuts and bolts, tighten if necessary
• to lubricate moving parts in order to minimize wear.
• to check all covers of screws and sharp edges and replace if necessary
• to replace defective parts according to the manufacturer's instructions
• to check swing seats, chains, ropes and other means of attachments for evi-
dence of deterioration
DISPOSAL ADVICE
At the end of the product's life, please dispose of it at an appropriate collection
point in your area. Local waste management companies will be able to answer
your questions on this.
SERVICE
We make every effort to deliver faultless products. If faults do arise however, we
put just as much effort into rectifying them. You can find numerous information
on the product, replacement parts, solutions to problems and lost assembly ma-
nuals at http://www.hudora.de/.
4/8
Publicidad
