Publicidad
Idiomas disponibles
Idiomas disponibles
DESCRIPTION
The Craftsman
Dust Collector
is designed
to remove
and col-
lect wood
dust and wood
chips from woodworking
machinery.
Collector
bag collects
dust and chips,
and makes
disposal
of
dust and chips easy. Collector
features
2_/2x 72" intake
hose.
SPECIFICATIONS
Motor
Horsepower
(Max.
Developed)
.................
1 _t_
Voltage
......................................
115 V
Amperes
.......................................
9.0
Hertz
..........................................
60
Phase .......................................
Single
RPM .........................................
3450
Certification
...................................
CSA
Air Flow Rate
..............................
150 CFM
Air Velocity
................................
4400
FPM
Maximum
Static
Pressure
...........
3.75"
of water
column
Sound
Level
................................
76 dB A
Inlet
..........................................
2I/Z
Collector
Bag Capacity
................
36 gal. (4.9 cu. ft.)
Collector
Bag Rating
.........................
1 micron
Weight
......................................
55 Ibs
Overall
Size ...........................
173/4x 19 x 72"
DUST
COLLECTOR
DANGER:Do
not use this dust collector
in a flammable
or
explosive
atmosphere.
Do not use to collect
metal
shavings
or
dust Consult
National
Fire Protection
Association
(NFPA)
standards
before
setting
up a dust collection
system,
espe-
cially
NFPA 664.
•
Connect
collector
hose to dust producing
machine
using
hose clamp.
NOTE:
For installations
with more than
one machine,
it is rec-
ommended
that Craftsman
22313
Shop
Dust Collection
System
be used for best performance.
NOTE:
A longer
hose may be used (maximum
length
is 40' of
2Yz" diameter
hose). A larger diameter
hose may be used,
but
length
will be decreased.
•
Turn dust collector
on before
starting
dust producing
machine.
EMPTYING
COLLECTOR
BAG
Refer to Figure
10.
DANGER:Turn
switch
off and remove
plug from
power
source
outlet
before emptying
collector
bag.
•
Empty
collector
bag by lifting bag clamp handle
and
releasing
spring
connector
from
latch. Slide
bag away from
collar. Dispose
of dust properly.
•
Mount
collector
bag by sliding
bag over opening on collar.
Position
the spring
connector
into one of the slots
on the
latch and lock the clamp
handle.
Make sure collector
bag
is secure
and rests flat on floor,
so that floor
supports
the
weight
of wood
dust and chips.
WARNING:
Turn switch
off and remove
plug from power
source
outlet
before maintaining
your dust collector.
Refer to Figure
10.
•
Clean
motor
of dust, chips
or other particles.
If operation
is
excessively
dusty or dirty, frequent
inspection
of motor
is
required.
Vacuum
any particles
that may have entered
the
motor.
•
Replace
worn,
cut or damaged
line cord.
•
Replace
worn
or damaged
collector
hose.
•
Replace
worn
or damaged
collector
bag.
•
Clean
or replace
filter on a regular
basis.
•
Frequently
check
that all nuts, bolts, screws,
etc. have not
loosened
due to collector
vibration.
CLEANING
OR
REPLACING
FILTER
DANGER:
Turn switch
off and remove
plug from
power
source
outlet
before maintaining
your dust collector.
Refer to Figure
5, Page 4.
•
Remove
collector
bag.
•
Remove
collar
by pushing
flex-ring
away from collar.
•
Reach
into collector
housing
and pull down on loop at top
of filter.
•
Clean
inside
of filter using vacuum.
•
Reinstall
filter.
•
Reinstall
collector
bag.
6
Publicidad
