Publicidad
EN
Safety instructions for battery charging
Caution! Before starting charging, make sure that the power unit body, cable and plug are not cracked or damaged. It is forbidden
to use a defective or damaged charging station and power unit! Use only the supplied charging station and power unit to charge
the batteries. The use of another power unit may result in fi re or damage to the tool. The battery should only be charged in a
closed, dry room, protected against unauthorised access, especially by children. Do not use the charging station and power unit
without the constant supervision of an adult! If you need to leave the room where the product is being charged, disconnect the
charger from the mains by removing the power unit's plug from the mains socket. If smoke, suspicious odours, etc. are escaping
from the charger, remove the charger plug from the mains socket immediately! The device is supplied with an uncharged battery
and should therefore be charged according to the procedure described below with the included power unit and charging station
before use. Li-ion (lithium-ion) batteries do not have the so-called "memory eff ect", which means they can be recharged at any
time. However, it is recommended to discharge the battery during normal operation and then charge it to full capacity. If, due to
the nature of work, it is not possible to use the battery in such a manner every time, it should be done at least every several work
cycles. Never discharge any batteries by short-circuiting the battery plates, as this will cause irreparable damage! In addition, do
not check the battery charge status by short-circuiting the electrodes and checking their sparking.
Storing the battery
Ensure proper storage conditions to extend the battery's life. The battery can last for approximately 500 charge-discharge cycles.
Store the battery at a temperature ranging from 0ºC to 30ºC at a relative air humidity of 50%. Charge the battery to approx. 70%
of its total capacity to store it for a longer period of time. In case of prolonged storage, the battery should be periodically charged
once a year. Do not over-discharge the battery as this will shorten its life and may cause irreparable damage. During storage,
the battery will gradually discharge due to leakage. The self-discharge process depends on the storage temperature – the higher
the temperature is, the faster the discharge process is. If the batteries are stored incorrectly, the electrolyte may leak. In case of
leakage, secure the leak with a neutralising agent. In the case of electrolyte contact with eyes, rinse eyes thoroughly with water,
and immediately seek medical attention. It is not allowed to use the tool with a damaged battery. If the battery is completely
worn, return it to a specialist waste disposal centre.
Transporting the batteries
Lithium-ion batteries are treated as hazardous goods according to legal regulations. The user of the tool can transport the product
together with the battery and the batteries alone by land. In that case, no additional conditions have to be met. If you entrust trans-
port to third parties (e.g. a courier company), follow the regulations regarding the transport of hazardous goods. Before shipping,
please contact a properly qualifi ed person. It is not allowed to transport damaged batteries. For the duration of transport, remove
the demountable batteries from the product and secure the exposed contacts, e.g. by covering them with insulation tape. Protect
the batteries in the packaging in such a way that they do not move inside the packaging during transport. National regulations for
the transport of hazardous materials must also be observed.
Charging the battery
Caution! Before charging, disconnect the charging station power unit from the mains by removing the plug from the mains socket.
In addition, clean the battery and battery clamps of dirt and dust with a soft, dry cloth.
The battery has a built-in charge indicator. The LEDs will light up by pressing the button (VII), the more of them come on, the more
charged the battery is. If the LEDs do not light up when the button is pressed, the battery is discharged. Disconnect the battery
from the tool. Slide the battery into the charger socket (VIII). Plug the charger into a mains socket. The red LED will light up, which
indicates the charging process. When charging is complete, the red LED will turn off and the green LED will light up to indicate
that the battery is fully charged. Pull the power unit plug out of the mains socket. Pull the battery out of the charging station by
pressing the battery latch button.
Caution! If the green LED lights up when the charger is connected to the mains, the battery is fully charged. In this case, the
charger will not start the charging process.
PRODUCT MAINTENANCE AND STORAGE
Whenever work is completed, disconnect the batteries from the product and proceed with maintenance. Ensure that the device is
unplugged. Remove the nozzle. To do this, press and hold the nozzle lock button, pull the nozzle off the blower. Do not remove
the nozzle by force or with tools to avoid damaging the unit. Clean both the ventilation openings and the inlet and outlet with a
soft handheld brush or a painting brush with plastic bristles. Clean the housing, handle, and controls with a soft, slightly dampened
with water cloth and then dry them. A compressed air stream with a pressure not exceeding 0.3 MPa can be used for cleaning.
Once the nozzle is removed, it can be cleaned with a jet of water and then dried or left to dry. Do not use sharp objects, abrasives,
solvents, or alcohol for cleaning.
Product storage
Store the product disassembled. The storage area should guarantee that unauthorised access to the product is prevented. The
storage area must be protected from moisture, direct sunlight, and excessively low temperatures. Store the product in a temper-
ature range 0~+40°C with a maximum relative humidity of 80%. It is recommended to store the product in the original packaging.
O R I G I N A L
I N S T R U C T I O N S
16
Publicidad
