Publicidad
English – Installation instruction
ATTENTION: Before starting to install and work with this device, please
read the Safety Instructions. This device shall only be connected to power
supplies compliant to EN62368-1, Annexe Q & Q.1 ("limited power
source").
When changing or installing a SPCW220 on the SPC system, ensure that
all anti-static precautions are adhered to while handling connectors, wires,
terminals and PCBs.
RISK OF DAMAGE TO THE DEVICE:
•
Use the device only indoors and in dry environments.
•
Do not expose it to dripping or splashing water.
•
Do not let the contact areas of the board get dusty and do not touch
them with your bare hands.
EC Declaration of Conformity
Hereby, Vanderbilt International (IRL) Ltd declares that this radio equipment type is
in compliance with all relevant EU Directives for CE marking.
•
Directive 2014/30/EU (Electromagnetic Compatibility Directive)
•
Directive 2014/35/EU (Low Voltage Directive)
•
Directive 2014/53/EU (Radio Equipment Directive)
•
Directive 2011/65/EU Restriction of the use of certain hazardous
substances Directive)
The full text of the EU declaration of conformity is available at
http://pcd.vanderbiltindustries.com/doc/SPC.
Product Description
The SPCW220 is an alternative interface for the SPC 2Way wireless devices. Only
one interface is permitted per SPC system; the SPCW120 mounted directly in the
SPC panel or the SPCW220 mounted remotely from the SPC panel.
The SPCW220 comprises of two main component parts;
•
The RS422 interface PCB that must be fitted to the SPC panel (Fig. 5).
•
The remote transceiver interface module complete with a SPCW120 (Fig.
6, item 3).
The SPCW120 transceiver provides a wireless interface for the SPC
controller that enables wireless devices (for example, magnetic contacts,
motion detectors, and remote controls) to be enrolled on the system.
Opening the SPCW220 Housing
To open the SPCW220 housing:
1. Unscrew the two cover fixing screws (Fig: 4, item 2).
2. Open the lid through 90° to the right (the lid is hinged on the left).
Controls and Indications
Controls
For normal operation, removeJumper 4 (Fig. 6, item 4) and leave Jumper 5 (Fig.
6, item 5). (See also Fig. 7.)
Indications
SPCW220
•
LEDs flash green when the SPCW220 is communicating with the SPC.
•
Red LED confirms that the device has 12v DC power when illuminated
RS422 Interface Board
•
Red LED, LED 1 – Power is on
•
Green LED, LED 2 - Communication from SPC to RS422 I/F
•
Green LED, LED 3 – Transmitting
Installation
Generally, the best location for the SPCW220 is centrally and elevated within the
protected building (Fig. 1). As buildings differ in construction & material, the best
location for each building can only be determined by site survey.
You must install the SPCW220 vertically as shown (Fig. 3, 4).
Installing the SPCW220 in any other orientation will impair the
performance of the antenna.
Avoid installing the SPCW220 on or near large metal objects
1. Disconnect the mains supply and then the battery in the the remote power
source (SPC panel or PSU).
2. Remove the lid from the SPCW220.
3. Secure the SPCW220 enclosure to the building fabric using the 4 mounting
holes (Fig.3, items 3).
Observe the "This way up" symbol (Fig. 3, item 1) on the SPCW220
enclosure. Mount the device in portrait , not in landscape orientation.
4. Open the SPC panel.
5. On the panel PCB, identify slot 2 to mount the RS422 interface board (Fig. 5,
item 1).
6. Carefully insert the RS422 interface board into the correct slot.
The SPCW220 is now ready for electrical connection.
Electrical Connection
Connecting the remote power source (SPC or PSU).
1. Disconnect the mains supply and then the battery in the the remote power
source (SPC or PSU).
2. Bring the connection cable into the enclosure through the access holes (Fig. 3,
item 6).
3. Secure the cable using the anchor points (Fig. 3, item 7).
4. Observing the correct polarity, connect the 12V DC supply and the tamper
signal wire.
5. Reconnect the mains supply and then the battery.
Your SPC panel is now ready to discover wireless devices.
For connection in Fig. 2B, link the 0v line from the SPC panel to the
SPCW220.
SPC to SPCW220 (Fig. 2A)
Tx+
Tx-
Rx+
Rx-
Reset
Reset
12v
0v
Zone
Zone
SPC to SPCW220 (Fig. 2B)
Tx+
Tx-
Rx+
Rx-
Reset
Reset
PSU 0v link
SPCW220 to remote PSU (Fig. 2B)
12v
0v
SPCW220 to Expander (Fig. 2B)
Zone
Zone
Tamper Connection
The tamper must be connected to a zone in the SPC panel. The zone type must
be Tamper.
Vanderbilt recommend that you assign a text identifier to aid in establishing the
location of the SPCW220.
The connection details are shown in Fig. 7.
Upgrade to an existing system
When installing the SPCW220 as an upgrade to an existing SPC 2Way Wireless
system, follow these steps:
1. Remove the SPCW120 from slot 2 in the SPC panel. The original antenna is
not now required.
2. Insert the RS422 interface board into slot 2 of the SPC panel. (Fig: 5, item 1).
3. Remove the SPCW120 from the SPCW220 and replace it with the SPCW120
from Step 1. (Fig. 6, item 1)
4. Remove the existing antenna and add it to the SPCW120 from the SPC panel
(Fig. 6, item 2).
5. Retain the SPCW120 from Step 3 for the next SPC 2Way Wireless project.
The devices that are already registered on the SPC system are stored in the
SPC and the SPCW120 registers. By moving the SPCW120 from the SPC
panel to the SPCW220, the data within these registers are retained, the
system is fully operational and is ready to accept new devices.
Compatibility Statement
This device only works with the Vanderbilt 2Way wireless devices and does not
work with any of the Si-Way devices.
Compatible 2Way wireless devices
Article Number
Description
SPCW120.000 Wrls. Panel txer w.
V54554-B106-A100
Antenna
V54538-F124-A100
WPIR-EXT AM Wrls. Ext PIR c/w pet
V54538-F113-A100
WSMK Wireless smoke alarm
V54538-F109-A100
WPIR Wireless 12m PIR detector PET
V54543-F154-A100
WKP-SIM keypad with fobs
V54538-F114-A100
WMAG-I Wrls. Magnetic Contact w. input
V54554-F107-A100
WRPTR Wireless Signal Repeater Plug
V54538-F111-A100
WMAG Wireless Magnetic Contact Slim
V54538-F116-A200
WSIR-EXT-R Wireless external bell red
V54538-F116-A100
WSIR-EXT-B Wireless external bell blue
V54538-F141-A100
WMAG-S Wireless Mag Cont & shock
V54538-F115-A100
WSIR-INT Wireless internal siren
V54543-F117-A100
WRMT Remote control w. 4 button
V54538-F116-A300
WSIR-EXT-O Wireless ext. bell orange
V54538-F110-A100
WPIR-CRT Wireless curtain PIR detector
V54543-F118-A100
WPAN Wireless personal alarm button
V54538-F117-A100
WGB Wireless Glass Break Detector
V54538-F118-A100
WFLOOD Wireless Flood Detector
Compatible Control Panels
Description
Article Number
SPC42
SPC42 intrusion controller grade 2
SPC52
SPC52 intrusion controller grade 2
SPC53
SPC53 intrusion controller grade 3
SPC63
SPC63 intrusion controller grade 3
V54541-C109-B100
SPC4320.320-L1 Intrusion CP, G2
V54541-C106-B100
SPC5320.320-L1 Intrusion CP, G2
V54541-C107-B100
SPC5330.320-L1 Intrusion CP, G3
V54541-C105-C100
SPC6330.320-L1 Intrusion CP, G3
Core
1
2
3
4
5
6
7
8
9
10
Core
1
2
3
4
5
6
7
Core
1
2
Core
1
2
SPCW220
X
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
Publicidad
