DeWalt DCE555 Manual De Instrucciones página 29

2. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light switch
which turns power off when you turn out the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non‑metallic brush. Do not use water or
any cleaning solutions.
Wall Mounting
Some D WALTchargers are designed to be wall mountable
e
or to sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet, and
away from a corner or other obstructions which may impede
air flow. Use the back of the charger as a template for the
location of the mounting screws on the wall. Mount the
charger securely using drywall screws (purchased separately)
at least 1" (25.4 mm) long, with a screw head diameter of
0.28–0.35" (7–9 mm), screwed into wood to an optimal
depth leaving approximately 7/32" (5.5 mm) of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start‑up can cause injury.
Installing and Removing the Bit (Fig. A)
This tool is designed for spiral cutting bits with either a 3 mm
(1/8"), 4 mm (5/32") (4 mm collet sold separately), or 6 mm
(1/4") shank and has a tool-free bit change system. To change
bits, FIRST turn off the tool and disconnect the battery from
the tool. Remove the cutting depth guide
1. To replace bit, depress both spindle lock button
collet lock 5 and turn collet grip
2. Insert or remove bit.

WARNING: The bits are sharp and should be handled
with great care.
2 .
7 and
6 counterclockwise.

CAUTION: When replacing bits, do not insert cutting
flutes into the collet. This may result in broken bits.
3. While depressing both spindle and collet locks, turn
the collet grip clockwise to firmly tighten the collet. For
some heavy duty applications, it may be necessary to
use a wrench to further tighten the collet nut
depressing the spindle lock button
4. Reattach the cutting depth guide.

CAUTION: Never tighten the collet without a
bit installed.
This tool comes with both 3 mm (1/8") and 6 mm (1/4")
collets. To change collets, remove the collet nut and insert
the desired collet. Always use a collet with a matching
diameter to that of the bit being installed.
Recommended Bits
Design SKU
Pilot Point DWAPP18010
DWAPP18010
DWAPP53202
DWAPP14002
Standard Point DWAST18010
DWAST18020
Multi‑Material DWAMM18005
DWAMM53202
Depth Guide (Fig. A)
Cutting depth guide 2 snaps onto locators as shown. Keep
depth guide in place at all times during operation of the tool.
For best results, adjust the cutting depth guide using the
knob to allow the bit to protrude about 6.35 mm past the
thickness of material to be cut. Ensure that when cutting, the
entire material thickness will engage with the bit's flutes.
Attaching the Dust Shroud (Fig. A, H)
The DCE555DC dust shroud (sold separately) is also available
for use with this tool. This accessory connects to the tools
cutting depth guide to function as both a cutting depth
guide and a dust shroud. It is compatible with the DWH161
D WALT Universal Dust Extractor (sold separately).
e
To attach the dust shroud, FIRST turn off the tool and
disconnect the battery from the tool.
1. Remove the cutting depth guide
2. Fully unscrew the knob and separate the knob
the washer 17 from the cutting depth guide
3. Replace the front portion of the cutting depth guide with
the dust shroud 14 .
4. Rethread the washer and the knob and tighten into the
base of the cutting depth guide.
5. Snap dust shroud/cutting depth guide onto the tool.
ENglIsh
4 while
7 .
Diameter Pack Quantity
1/8" 10
1/8" 20
5/32" 2
1/4" 2
1/8" 10
1/8" 20
1/8" 5
5/32" 2
2 .
16 and
2 .
27