cecotec CONGA ROCKSTAR 2500 X-TREME ERGOFLEX Manual De Instrucciones página 26

ENGLISH
Using the vacuum cleaner
Press the On/off button to turn the device on and off.
-
Press the speed button repeatedly to select the device operating speed: LOW, MED, HIGH
-
and AUTO. The device is by default switched on in LOW mode.
If you select the AUTO mode, the device will automatically adjust suction power according
-
to the concentration of dust and the type of surface.
When operating at high speed, if the battery is at 20% or lower, the device will automatically
-
switch to medium speed in order to lengthen the battery life.
Using the brush head
Assemble the vacuuming tube to the main body and the brush head to the tube, as
-
described in the product assembly section.
Press the On/off button to turn the device on and off.
-
Press the speed selector to adjust the power level between LOW, MED, HIGH and AUTO
-
modes.
The brush head removes dust from carpets, hard and soft floors, and tiles.
-
If too many particles or fibres are vacuumed, or if a child touches the brush during operation
-
by accident, the rotary brush stops spinning automatically in order to prevent tangles and
possible damage.
Accessories
Fig. 4
This device includes different accessories that allow cleaning different types of surfaces,
objects and dirt. Some of them are suitable for the upright vacuum cleaner, and others are
preferably used with the handheld one.
Jaliscazo brush
Assemble this brush to the upright vacuum cleaner. This brush is especially designed for
cleaning hard floors, but can be used to efficiently clean soft floors too.
2-in-1 wide accessory for corners and furniture
Fig. 5
This accessory is preferably used with the handheld vacuum cleaner and allows cleaning
furniture without damaging it and reaching less accessible dirt in corners.
2-in-1 narrow accessory for corners and furniture
Fig. 6
This accessory is preferably used with the handheld vacuum cleaner and allows cleaning
furniture without damaging it and reaching less accessible dirt in corners.
50
Vacuuming flexible tube
Use the Flex tube to access and vacuum dirt from the most difficult areas. Press the Flex
button to bend the tube.
Wall charging base installation
Fig. 7
Place the charging base on the wall and mark the 3 holes to be drilled in order to fix the
1.
base. Take into account the height of the installation, it is important that the brush head
rests on the floor to avoid the charging base from holding all the vacuum cleaner's weight.
Drill 3 holes in the wall (previously marked) and insert the pegs and M4 x 32 mm screws.
2.
Make sure that the charging base is securely fixed on the wall, place the vacuum cleaner
3.
on the charging base by putting the vacuum cleaner charging terminals into contact with
the terminals of the charging base (plastic tab).
Once the wall charging base is installed, the charging port must be connected to the
4.
power adapter, and then the device can be charged by sliding it from top to bottom into
the wall charging base. Fig. 8
Charge and display
When the battery percentage is 20 % or below, the device will automatically enter
-
low consumption mode. It is recommended to charge the device when it reaches this
percentage.
The battery must be charged on the charging base while connected to the device. Connect
-
one of the ends of the power adapter to the power supply and the other to the charging
base. Fig. 8
During charging, the charge light indicator will turn on red and the display will show the
-
current charge percentage. When the device is fully charged, the battery indicator will turn
green and the display will show 100 %. Fig. 9
You can also charge the battery without using the charging base. It can be charged when
-
the battery is installed or not in the device. Connect the adapter and connect the other end
to the battery, paying attention to the direction. Once it is properly connected, the charge
light indicator will turn on red and will turn green once the charge is complete. Fig. 10-11
5. CLEANING AND MAINTENANCE
Turn the appliance off, unplug it from the power supply and allow it to cool down before
-
cleaning it.
Use a soft, slightly dampened cloth to clean the device surface.
-
Never immerse the device in water or other liquids, do not allow liquids to enter the device.
-
Do not use abrasive cleaners or scouring pads to clean the product.
-
Do not leave the device in a place with direct sunlight.
-
ENGLISH
CONGA ROCKSTAR 2500 X-TREME ERGOFLEX 51