Publicidad
Idiomas disponibles
Idiomas disponibles
Installation
5. Peel backing off one side of Adhesive Mounting Pad
to outside of Mounting Cap
, as shown.
L
Peel backing off other side of Adhesive Mounting Pad, and place
Mounting Cap over end of Adjustment Bumper
NOTE: Make sure gate stays straight up and down (90º to floor) and
in center of door frame during this process.
Slide Adjustment Bumper
out of gate frame toward door frame,
C
until Mounting Cap sticks to door frame. Repeat this for other three
Mounting Caps.
OPTIONAL: If mounting to drywall, mark center of mounting caps.
Pull mounting caps off wall. Drill holes and insert wall anchors.
Secure mounting caps with screws. Tighten all four screws securely
with handheld Phillips screwdriver, but do not overtighten.
6. Using the wrench, turn both upper Adjustment Bumpers
lower Adjustment Bumpers
, as shown, until all four rubber ends
E
contact the mounting caps.
Check that the gate is still straight up and down then turn each
bumper two more full rotations or until tight.
7. Test to make sure the gate frame assembly is secure by firmly
shaking it. If it moves, it needs to be re-installed. Repeat steps 5 – 6.
WARNING
BEFORE removing the YELLOW TAG and cutting the
PLASTIC TIES, ENSURE the gate is securely in place
or serious injury may result.
8. With your gate securely in place, remove the yellow tag then cut
and discard the plastic ties.
4
. Adhere pad
K
K
.
C
L
Mounting
Cap
Wall
Anchor
D
and both
D
WARNING
Distance between gate frame and door frame
should be equal on both sides, and NEVER
exceed 5 cm (2 in).
9. Adjust both upper bumpers
the button
F
and latch
C
10. Inspect the gate door. Make sure it swings freely and
latches securely.
C
1. To open gate, slide button H while lifting gate door slightly I and
swing the gate open.
2. When window J is red, gate is NOT latched.
Screw
3. To close gate, push door gently.
• Wash gate with mild soap and warm water and dry thoroughly before using.
• Metal and plastic parts can be wiped clean with a soft damp cloth and dried with a soft cloth. DO NOT use abrasive cleaners
E
or solvents.
• Remember to clean rubber ends of adjustment bumpers with rubbing alcohol before each use.
For a period of 90 days from the original purchase of this Product, Evenflo warrants to the original end user ("Purchaser") this
Plastic Tie
Product (including any accessories) against defects in material or workmanship. Evenflo's sole obligation under this express limited
warranty shall be, at Evenflo's option, to repair or replace any Product that is determined to be defective by Evenflo and determined
to be covered by this warranty.
Repair or replacement as provided under this warranty is the exclusive remedy of the Purchaser. Proof of purchase in the form of
a receipted invoice or bill of sale evidencing that the Product is within the warranty period must be presented to obtain warranty
service. This express limited warranty is extended by Evenflo ONLY to the original Purchaser of the Product and is not assignable
or transferable to subsequent purchasers or end users of the Product. For warranty service, contact Evenflo's ParentLink Consumer
Resource Center at (800) 233-5921 or www.evenflo.com.
Yellow
Tag
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS HEREBY DISCLAIMED. EVENFLO SHALL NOT BE
LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL OR PUNITIVE DAMAGES OF ANY KIND FOR BREACH
OF THE EXPRESS LIMITED WARRANTY ON THIS PRODUCT, OR ANY WARRANTY IMPLIED BY OPERATION OF LAW.
OTHER THAN THE EXPRESS LIMITED WARRANTY SET FORTH ABOVE, THERE ARE NO OTHER WARRANTIES THAT
ACCOMPANY THIS PRODUCT, AND ANY ORAL, WRITTEN OR ANY OTHER EXPRESS REPRESENTATION OF ANY KIND
IS HEREBY DISCLAIMED.
Plastic Tie
D
until the gap between
D
G
is 3.2 mm (1/8").
www.evenflo.com • USA: 1-800-233-5921, 8 AM – 5 PM EST
• Canada: 1-937-773-3971 • México: 800-706-1200
D
F
3,2 mm
(1/8 in)
G
Gate Operation
H
J
I
Care and Maintenance
Limited Warranty
5
Publicidad
