camry Premium CR 7973 Manual De Uso página 9

8. To reduce the formation of scale in the water, the machine is equipped with a water descaling filter (13), a plastic disc that you will find
inside the water tank. Do not throw away the filter (13) when changing water, the filter is active for 1 year, you can optionally purchase a
filter for this device, number CR7973.1 from the seller of this device.
AROMATHERAPY FUNCTION
1. Remove the rotating cap (1).
2. Pour 2-3 drops of essential oil onto an aromatherapy cotton sponge (11) and place it in place (4). See picture 3. The nice fragrance
will be distributed with the mist.
NOTE: ONLY water-soluble essential oils are suitable for this device.
3. DO NOT drip essential oils directly into the water.
USAGE
1. After connecting, the device beeps and goes into standby mode.
2. To turn on the device, press the power button (7A) once. The default mist volume is set to the first level, the display (8) will show the
number 1, to put the device into standby press the button (7A) again.
3. Press the button (7C) several times to set the mist intensity. The display (8) will show numbers from 1 to 5 in turn, where 1 means low
fog intensity and 5 means the maximum low mist intensity. See figure 4.
PROTECTION AGAINST LACK OF WATER
When the device is running, the float (14) detects the lack of water. Then the device stops working, a flashing red symbol of crossed-out
drop appears on the display (8) (see Figure 1), after 30 seconds the device goes into standby mode. After adding water, press the power
button (7A), after which the device can work normally.
TIMER SETTING & SLEEP MODE SETTING
The default setting is zero hours. While the device is running, press the timer button (7B) repeatedly to select one of the timer periods: 1
hour or 2 hours or 4 hours or 8 hours or keep pressing the button (7B) further to select one of the three night mode settings:
01: when entering sleep mode, "01" flashes for 5 seconds, then turns off the display, sprays fog for 1 minute, and stops for 1 minute, it
works in such cycles.
05: when entering sleep mode, "05" flashes for 5 seconds, then turns off the display, sprays fog for 5 minutes, and stops for 5 minutes, it
works in such cycles.
10: when entering sleep mode, "10" flashes for 5 seconds, then blanks the display, sprays for 10 minutes and stops for 10 minutes, it
works in such cycles.
See figure 6.
SETTING THE HUMIDITY LEVEL
When the device is working, press the continuous humidification button (7D), you can set the humidity value in the range of 40-90%
relative humidity, each subsequent press increases the value by 5%. Once the humidity level is set, the device continuously humidifies to
the desired level. When the desired humidity level is reached, the device goes into standby mode and stops spraying the mist until the
ambient humidity level drops to 5% below the desired humidity level. In this case, the device will start spraying the mist automatically
again. Refer to figure 5. When you set the desired humidity value, this number flashes, when the selection is completed, the flashing will
stop after 5 seconds. The display (8) shows the current room humidity and temperature alternately.
CLEANING AND MAINTENANCE
1. Unplug the device before cleaning. If there is some water left in the water tank (6), pour it out by tilting the water tank (6). See figure 2.
NOTE: It is important to position the water tank (6) correctly when pouring out the water. The correct position is obtained when the air
outlet (16) remains dry and the water flow is guided by the opposite edge of the water tank (6). See figure 2.
2. Clean the water tank every 3 days.
3. After using the device for a while, scale is easily deposited and "white powder" phenomenon is formed, it is attached to the surface of
the atomizing transducer (17), which affects the humidification performance. It is necessary to clean the main elements regularly. To
clean the main components, see Figure 7.
* Open the water tank cover (2), remove the water tank (6).
* Add appropriate amount of water, clean the device with the cleaning brush (12).
* Wipe the atomizing transducer (17) with a cotton swab soaked in a solution of citric acid and do not touch it with sharp, hard objects.
* Wipe the inside of the water tank (6), mist air duct (5) and covers with a soft dry cloth.
4. Do not use detergent to clean, clan water is better.
5. The outer surface of the device housing can be cleaned with a damp cloth and then wiped dry with a clean cloth. Do not use chemical
solvents, gasoline, kerosene or polishing powder to wipe the surface.
6. Do not allow water to enter the housing during cleaning to avoid malfunction of internal components.
7. Clean the device before each use.
STORAGE
1. For seasonal storage, keep the device empty, clean and dry.
9