Publicidad
Idiomas disponibles
Idiomas disponibles
pushing the rear part.
• Fix the adhesive rubber under the LED strip at the curve to
protect it from the sharp aluminium profile (detail F).
• Insert the transparent profiles in the boom.
• Pass the LED light strip cable through the centre hole of the
boom support (detail G).
• Push the cable out of the opposite end of the gear motor unit
through the rubber cable guide to the centre of the spring
linkage lever (Fig. 7).
• Introduce the cable into the rubber cable guide present in the
barrier support structure.
• Introduce the cable into the control unit, ensuring that the
cable will not interfere with the movements of the automation
system.
FOR ALED LIGHT CONNECTIONS: connect the cable to the control
unit as shown in fig. 8. Connect the brown (or red) wire to the
+LUCI terminal and connect the blue (or black) wire to the COM
terminal.
Refer to parameter 79 of the control unit for setting up the LED
light strip.
FOR ALED/RGB LIGHT CONNECTIONS: make connections with
ALED/RGB and refer to RGB light operation modes see figure 13
and installation manual B73/LTM.
4.4
Installation procedure BIONIK8
If the arm is mounted on the barrier's body, remove it.
Place the arm on a stable surface, making sure it is not scratched.
To insert the LEDs, proceed as follows (Fig. 9):
• Unscrew the 6 M8 screws and remove the boom support cover
(detail D).
• Unscrew the 2 TCC 4,2x13 screws and remove the cap of the
boom (detail E).
• Insert the LED light strip [F] inside the PVC profile, with the
LEDs upwards, until it comes out from the opposite end.
• Fold the excess length of LED light strip into the aluminium
moulding and fasten it with the cable tie included (detail G).
• Pass the LED light strip cable through the centre hole of the
boom support (detail H) Fig. 10.
• Push the cable out of the opposite end of the gear motor unit
through the rubber cable guide to the centre of the spring
linkage lever (detail I, fig. 11).
• Introduce the cable into the rubber cable guide present in the
barrier support structure.
• Introduce the cable into the control unit, ensuring that the
cable will not interfere with the movements of the automation
system.
FOR ALED LIGHT CONNECTIONS: connect the cable to the control
unit as shown in fig. 12. Connect the brown (or red) wire to the
+LUCI terminal and connect the blue (or black) wire to the COM
terminal.
Refer to parameter 79 of the control unit for setting up the LED
light strip.
FOR ALED/RGB LIGHT CONNECTIONS: make connections with
ALED/RGB and refer to RGB light operation modes see figure 13
and installation manual B73/LTM.
5
Initial testing
Unlock the barrier, lift and lower the boom by hand and check that
the LED light strip cable is not tautened excessively and does not
interfere with the movements of the automation system.
Confirm the lighting of all LEDs with automation in motion.
In the case of the RGB version, check that the colours red and
green (depending on the chosen mode) and also blue (only used
in the stand-by function) light up.
6
Maintenance
Perform scheduled maintenance every 6 months.
Check cleanliness and correct functioning.
If any dirt, moisture, insects or other foreign matter is found in
the unit, disconnect from mains power and from the batteries and
clean.
Repeat the initial installation test procedure after cleaning.
7
Disposal
This product may only be uninstalled by qualified
technical personnel, following suitable procedures for
removing the product correctly and safely. This product
consists of numerous different materials. Some of these
materials may be recycled, while others must be
disposed of correctly at the specific recycling or waste
management facilities indicated by local legislation applicable for
this category of product.
Do not dispose of this product as domestic refuse. Observe local
legislation for differentiated refuse collection, or hand the product
over to the vendor when purchasing an equivalent new product.
Local legislation may stipulate severe fines for the incorrect
disposal of this product. Warning! some parts of this product
may contain substances that are harmful to the environment or
dangerous and that may damage the environment or pose a risk
to health if disposed of incorrectly.
8
Additional information and
contact details
ROGER TECHNOLOGY is the exclusive owner of all rights
regarding this publication.
ROGER TECHNOLOGY reserves the right to implement any
modifications without prior notification. Copying or scanning of
or any alterations to this document are prohibited without the
express prior permission of ROGER TECHNOLOGY.
ROGER TECHNOLOGY CUSTOMER SERVICE:
business hours:
Monday to Friday
8-12 am and 1.30-5.30 pm
Telephone no:
+39 041 5937023
E-mail:
service@rogertechnology.it
Skype:
service_rogertechnology
9
Declaration of Conformity
I the undersigned, as acting legal representative of the manufacturer:
Roger Technology - Via Botticelli 8 - 31021 Bonisiolo di Mogliano
V.to (TV)
hereby DECLARE that the appliance described hereafter:
Description: automatic barrier lights
Model: ALED
Is conformant with the legal requisites of the following directives:
- 2014/35/UE ;
- 2014/30/UE ;
- 2011/65/UE ;
and that all the standards and/or technical requirements indi-
cated as follows have been applied:
EN 61000-6-3:2007/A1:2011
EN 61000-6-2:2005
Place: Mogliano V.to
Date: 10-5-2014
Signature
19
Publicidad
