Whirlpool WSFC 3M17 X Manual De Instrucciones página 36

EN
OPTIONS AND FUNCTIONS
OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL). If an option is not compatible with the selected
program (see PROGRAMS TABLE), the corresponding LED flashes rapidly 3 times and beeps will sound. The option will not be enabled.
MULTIZONE - If there are not many dishes to be washed, a half load-
ing may be used in order to save water, electricity and detergent.
By default the appliance washes dishes in all racks.
SANI RINSE - This option can be used to sanitize washed dishes.
It will increase final rinse temperature and add antibacterial wash to the
selected program. WARNING: the crockery and plates could be extremely
hot at the end of the cycle.
LOADING THE RACKS
UPPER RACK
(loading example for the
upper rack)
Load delicate and light
dishes: glasses, cups, saucers,
low salad bowls.
CLEANING AND MAINTENANCE
CLEANING THE FILTER ASSEMBLY
2
1
A
In case you find foreign objects (such as broken glass, porcelain, bones, fruit seeds
etc.) please remove them carefully.
NEVER REMOVE the wash-cycle pump protection (black detail) (Fig 4).
TROUBLESHOOTING
In case your dishwasher doesn't work properly, check if the problem can be solved by going through the following list. For other errors or issues
please contact authorized After-sales Service which contact details can be found in the warranty booklet. Spare parts will be available for a period
of either up to 7 or up to 10 years, according to the specific Regulation requirements.
PROBLEMS POSSIBLE CAUSES
No water in the water supply or the tap is closed.
The dishwasher does not
fill the water. Display shows:
The inlet hose is bent.
and F6, both On/Off
and START/Pause LEDs are
The sieve in the water inlet hose is clogged; it is
blinking rapidly.
necessary to clean it.
Dishwasher finishes the cycle
Drain hose positioned too low or siphoning into
prematurely.
home sewage system.
Display shows: F15 and both
On/Off and START/Pause
Air in water supply.
LEDs are blinking rapidly.
Policies, standard documentation, ordering of spare parts and additional product information can be found by:
• Using QR code on your product.
• Visiting our website docs.whirlpool.eu and parts-selfservice.whirlpool.com
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When contacting our After-
sales Service, please state the codes provided on your product's identification plate.
The model information can be retrieved using the QR-Code reported in the energy label. The label also includes the model
identifier that can be used to consult the portal of the registry at https://eprel.ec.europa.eu.
36
LOWER RACK
(loading example for the
lower rack)
For pots, lids, plates, salad
bowls, cutlery etc.. Large
plates and lids should ide-
ally be placed at the sides
to avoid interferences with
the spray arm.
3
B
A
C
Please scan the QR code on your product in order to have more detailed information.
TABLET (Tab)- If you use powder or liquid detergent, this option
should be off.
DELAY -The start of the program may be delayed for a period of time
between 0:30 and 24 hours.
The DELAY function cannot be set once a wash cycle has been started.
KEYLOCK - A long press (for 3 seconds) of MULTIZONE button, will
activate the KEYLOCK function. To deactivate the KEYLOCK, long press again.
CUTLERY BASKET
FOLDABLE
The basket is equipped with top grilles for improved cutlery arrangement.
FLAPS
WITH AD-
The cutlery basket should be positioned only at the front of the lower rack.
JUSTABLE
POSITION
Knives and other utensils with sharp edges must be placed in the
cutlery basket with the points facing downwards or they must be po-
sitioned horizontally in the tip-up compartments on the upper rack.
CLEANING THE SPRAY ARMS
4
To remove the upper spray arm,
turn the plastic locking ring in a
clockwise direction.
Please scan the QR code on your product in order to have more detailed information.
SOLUTIONS
Make sure there is water in the water supply or the tap running.
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the dishwasher
and reboot.
After having carried out the verification and cleaning, turn off and turn on the dish-
washer and restart a new program.
Check if end of drain hose is placed at correct height (see INSTALLATION).Check for
siphoning into home sewage system, install air admittance valve if necessary.
Check water supply for leaks or other issues letting air inside.
CAPACITY: 10 standard place-settings
More information in the Daily Reference Guide on website.
Quick Guide
The lower spray arm may
be removed by pulling it
upwards.
IEC 436
:
400011696690
09/2023 jk - Xerox Fabriano