Publicidad
Idiomas disponibles
Idiomas disponibles
o
DRESS
PROPERLY
- Do not
wear
loose
clothing
or jewelry
They can be caught
in moving
parts.
Use of rubber
gloves
and
substantial
footwear
is recom-
mended
when
working
outdoors
Wear
protective
hair covering
to
contain
long hair.
o
DON'T
OVERREACH
- Maintain
proper
footing
and balance
at all
times
o
USE SAFETY
GLASSES-
Al-
ways wear
proper
eye protection,
and use face or dust mask
if op-
eration
is dusty.
o
MAINTAIN
UNIT
WITH
CARE-
Keep
cutting
edges
clean
for best
performance
and to reduce
the
risk of injury.. Follow
instructions
for lubricating
and service
Keep
handle
dry, clean,
and free from
oil and grease+
+
AVOID
UNINTENTIONAL
STARTING
- Don't
carry unit with
a finger
on the switch.
°
CHECK
DAMAGED
PARTS-
if the clipper
or blade
pack experi-
ences
a hard
impact,
check that
no parts were
damaged
and verify
that the unit operates
properly
Check
for misalignment
or bend-
ing of moving
parts,
breakage
of
parts,
and any other
condition
that
may affect
operation.
A part that is
damaged
should
be properly
re-
paired
or replaced
by an author-
ized service
center.
+
STAY
ALERT
-Watch
what you
are doing.
Use common
sense.
Do not operate
the too! when
you
are tired.
°
DON'T
GRASP
THE EXPOSED
CUTTING
BLADES
or cutting
edges
when
picking
up or holding
the unit. Do not attempt
to remove
cut material
nor hold material
to
be cut when
blades
are moving
Make sure the unit's
switch
is off
when
clearing
jammed
material
from
blades.
To reduce
risk when
using
charger:
+
DO NOT use charger
outdoors
or in
wet conditions;
use inside only,
•
DO NOT charge the unit when the
temperature
is below +40 F or
above +120 F
o This unit and its charger are des-
igned to work together,, DO NOT
charge the combo clipper with any
other charger and DO NOT use this
charger with any other appliance
o
The charger is designed to operate
on 120 volts, DO NOT attempt to
use it at any other voltage,,
SAVE THESE INSTRUCTIONS
o
CHARGE
BATTERY
PRIORTO
USE - The Combo
Clipper
does
not come fully charged
when
pur-
chased.
So before
using
the unit,
the battery
must
be charged,
Be-
fore charging
the batter€,
read
safety
and charging
instructions
o
PROPER
RUNTIME
AND
PER-
FOMANCE
can only be obtained
with a fully charged
battery
o
CHARGE
TIME-20
hours
of
charging
is sufficient
to replenish
the battery
to a full charge
Initial
use, long periods
of inactivity,
or
storage
at extreme
temperatures
may require
extended
charge
time
+
WALL
CHARGE
BRACKET-
Before
charging
the unit, make
sure the charge
bracket
is securely
attached
to the wall; attach
with
screws
to a walt stud, or use ap-
propriate
wall anchors.
To Charge
Battery:
1.. Plug the charger
into a 120 Volt AC
outlet,
2.
Place the Combo
Clipper
into the
wall charge
bracket.
3
The Combo
Clipper
is now in
charge+
4.
Charge
for at least 20 hours..
Charging
Notes:
o
CAUTION:
The charger
can be
used with 60Hz cycle,
and 1 I5-120
VAC
electricity
only
Publicidad
