*If you plan to leave the monitor unused for an extended period of time, or if you are going to be away from home
(especially if there are children, the elderly, or people with disabilities left alone), be sure to unplug the power plug or
power adapter from the outlet.
Accumulated dust may cause sparks and heat from the power cord or power adapter or cause the insulation of the power
cord or power adapter to deteriorate, resulting in electric shock, leakage or fire.
*After the monitor is moved from a low temperature place to a warm area, it should be placed for a period
of time before powering on, so that the condensation inside the monitor can be fully dissipated and dried.
*The power supply voltage will be marked on the back of the monitor, DC 24V.
*If you plan to install this product in dusty, high or low temperature, high humidity, chemical-containing environments
and 24-hour use locations (such as airports or train stations, etc.), be sure to contact an authorized service center for
further assistance. Otherwise, the monitor may be severely damaged.
*Be sure to use only properly grounded plugs and sockets. Poor grounding may result in electric shock or equipment
damage. (for Class I equipment only)
*To disconnect the power from the device, the power cord or power adapter plug must be unplugged from the machine,
so the power cord or adapter plug should be easily accessible.
*Children are prohibited from climbing on this product.
*Keep the accessory parts out of the reach of children.
*Do not install this product in an unstable location, such as a wobbly shelf, sloping floor, or a location subject to external
vibration.
*Do not drop the product or subject it to shock. If the product is damaged, please disconnect the power supply and
contact the service center in time for further assistance.
CAUTION
Risk of explosion if the battery is replaced by an incorrect type
*replacement of a battery with an incorrect type that can defeat a safeguard (for example,in the case of some lithium
battery types);
* disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of abattery, that can result in an explosion;
* leaving a battery in an extremely high temperature surrounding environment that canresult in an explosion or the leakage of
flammable liquid or gas;
*a battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
FCC Statement:
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
---Reorient or relocate the receiving antenna.
---Increase the separation between the equipment and receiver.
---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
---Consult the dealer or an experienced radio/TV technician for help.
IC Statement:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
WARNING:
Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
Radiation Exposure Statement:
This device has been evaluated and shown compliant with the RF exposure requirements listed in RSS-102 - Radio
Frequency (RF) Exposure Compliance of Radio communication Apparatus limits under fixed exposure conditions (antennas
are greater than 20cm from a person's body) when installed in certain specific OEM configurations.
Technical Specifications:
Operating temperature:-10°C - 45°C
Frequency range: 2.400 Ghz ~ 2.497 GHz (2.4 GHz)/5.1 GHz~5.9 GHz (5 GHz)
Max. RF Output Power: < 10dBm
Alternating current
3